u-boot/include/configs/x600.h

304 lines
9.6 KiB
C
Raw Normal View History

/*
* (C) Copyright 2009
* Vipin Kumar, STMicroelectronics, <vipin.kumar@st.com>
*
* Copyright (C) 2012, 2015 Stefan Roese <sr@denx.de>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_SPEAR600 /* SPEAr600 SoC */
#define CONFIG_X600 /* on X600 board */
#define CONFIG_SYS_THUMB_BUILD
#include <asm/arch/hardware.h>
/* Timer, HZ specific defines */
#define CONFIG_SYS_HZ_CLOCK 8300000
#define CONFIG_SYS_TEXT_BASE 0x00800040
#define CONFIG_SYS_FLASH_BASE 0xf8000000
/* Reserve 8KiB for SPL */
#define CONFIG_SPL_PAD_TO 8192 /* decimal for 'dd' */
#define CONFIG_SYS_SPL_LEN CONFIG_SPL_PAD_TO
#define CONFIG_SYS_UBOOT_BASE (CONFIG_SYS_FLASH_BASE + \
CONFIG_SYS_SPL_LEN)
#define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_MONITOR_LEN 0x60000
#define CONFIG_ENV_IS_IN_FLASH
/* Serial Configuration (PL011) */
#define CONFIG_SYS_SERIAL0 0xD0000000
#define CONFIG_SYS_SERIAL1 0xD0080000
#define CONFIG_PL01x_PORTS { (void *)CONFIG_SYS_SERIAL0, \
(void *)CONFIG_SYS_SERIAL1 }
#define CONFIG_PL011_SERIAL
#define CONFIG_PL011_CLOCK (48 * 1000 * 1000)
#define CONFIG_CONS_INDEX 0
#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, \
57600, 115200 }
#define CONFIG_SYS_LOADS_BAUD_CHANGE
/* NOR FLASH config options */
#define CONFIG_ST_SMI
#define CONFIG_SYS_MAX_FLASH_BANKS 1
#define CONFIG_SYS_FLASH_BANK_SIZE 0x01000000
#define CONFIG_SYS_FLASH_ADDR_BASE { CONFIG_SYS_FLASH_BASE }
#define CONFIG_SYS_MAX_FLASH_SECT 128
#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_FLASH_ERASE_TOUT (3 * CONFIG_SYS_HZ)
#define CONFIG_SYS_FLASH_WRITE_TOUT (3 * CONFIG_SYS_HZ)
/* NAND FLASH config options */
#define CONFIG_NAND_FSMC
#define CONFIG_SYS_NAND_SELF_INIT
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_BASE CONFIG_FSMC_NAND_BASE
#define CONFIG_MTD_ECC_SOFT
#define CONFIG_SYS_FSMC_NAND_8BIT
#define CONFIG_SYS_NAND_ONFI_DETECTION
#define CONFIG_NAND_ECC_BCH
#define CONFIG_BCH
/* UBI/UBI config options */
#define CONFIG_MTD_DEVICE
#define CONFIG_MTD_PARTITIONS
#define CONFIG_RBTREE
/* Ethernet config options */
#define CONFIG_MII
#define CONFIG_PHY_RESET_DELAY 10000 /* in usec */
#define CONFIG_PHY_ADDR 0 /* PHY address */
#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
#define CONFIG_PHY_MICREL
#define CONFIG_PHY_MICREL_KSZ9031
#define CONFIG_SPEAR_GPIO
/* I2C config options */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_BASE 0xD0200000
#define CONFIG_SYS_I2C_SPEED 400000
#define CONFIG_SYS_I2C_SLAVE 0x02
#define CONFIG_I2C_CHIPADDRESS 0x50
#define CONFIG_RTC_M41T62 1
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
/* FPGA config options */
#define CONFIG_FPGA
#define CONFIG_FPGA_XILINX
#define CONFIG_FPGA_SPARTAN3
#define CONFIG_FPGA_COUNT 1
/* USB EHCI options */
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_SPEAR
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
/*
* Command support defines
*/
#define CONFIG_CMD_DATE
#define CONFIG_CMD_ENV
#define CONFIG_CMD_FPGA_LOADMK
#define CONFIG_CMD_MTDPARTS
#define CONFIG_CMD_NAND
#define CONFIG_CMD_SAVES
#define CONFIG_CMD_UBIFS
#define CONFIG_LZO
/* Filesystem support (for USB key) */
#define CONFIG_SUPPORT_VFAT
#define CONFIG_DOS_PARTITION
/*
* U-Boot Environment placing definitions.
*/
#define CONFIG_ENV_SECT_SIZE 0x00010000
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \
CONFIG_SYS_MONITOR_LEN)
#define CONFIG_ENV_SIZE 0x02000
#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + \
CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
/* Miscellaneous configurable options */
#define CONFIG_ARCH_CPU_INIT
#define CONFIG_BOOT_PARAMS_ADDR 0x00000100
#define CONFIG_CMDLINE_TAG
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_MISC_INIT_R
#define CONFIG_BOARD_LATE_INIT
#define CONFIG_MX_CYCLIC /* enable mdc/mwc commands */
#define CONFIG_SYS_MEMTEST_START 0x00800000
#define CONFIG_SYS_MEMTEST_END 0x04000000
#define CONFIG_SYS_MALLOC_LEN (8 << 20)
#define CONFIG_SYS_LONGHELP
#define CONFIG_CMDLINE_EDITING
#define CONFIG_AUTO_COMPLETE
#define CONFIG_SYS_CBSIZE 256
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_MAXARGS 16
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
#define CONFIG_SYS_LOAD_ADDR 0x00800000
#define CONFIG_SYS_CONSOLE_INFO_QUIET
/* Use last 2 lwords in internal SRAM for bootcounter */
#define CONFIG_BOOTCOUNT_LIMIT
#define CONFIG_SYS_BOOTCOUNT_ADDR (CONFIG_SRAM_BASE + \
CONFIG_SRAM_SIZE)
#define CONFIG_HOSTNAME x600
#define CONFIG_UBI_PART ubi0
#define CONFIG_UBIFS_VOLUME rootfs
#define MTDIDS_DEFAULT "nand0=nand"
#define MTDPARTS_DEFAULT "mtdparts=nand:64M(ubi0),64M(ubi1)"
#define CONFIG_EXTRA_ENV_SETTINGS \
"u-boot_addr=1000000\0" \
"u-boot=" __stringify(CONFIG_HOSTNAME) "/u-boot.spr\0" \
"load=tftp ${u-boot_addr} ${u-boot}\0" \
"update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE) \
" +${filesize};" \
"erase " __stringify(CONFIG_SYS_MONITOR_BASE) " +${filesize};" \
"cp.b ${u-boot_addr} " __stringify(CONFIG_SYS_MONITOR_BASE) \
" ${filesize};" \
"protect on " __stringify(CONFIG_SYS_MONITOR_BASE) \
" +${filesize}\0" \
"upd=run load update\0" \
"ubifs=" __stringify(CONFIG_HOSTNAME) "/ubifs.img\0" \
"part=" __stringify(CONFIG_UBI_PART) "\0" \
"vol=" __stringify(CONFIG_UBIFS_VOLUME) "\0" \
"load_ubifs=tftp ${kernel_addr} ${ubifs}\0" \
"update_ubifs=ubi part ${part};ubi write ${kernel_addr} ${vol}" \
" ${filesize}\0" \
"upd_ubifs=run load_ubifs update_ubifs\0" \
"init_ubifs=nand erase.part ubi0;ubi part ${part};" \
"ubi create ${vol} 4000000\0" \
"netdev=eth0\0" \
"rootpath=/opt/eldk-4.2/arm\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
"nfsroot=${serverip}:${rootpath}\0" \
"ramargs=setenv bootargs root=/dev/ram rw\0" \
"boot_part=0\0" \
"altbootcmd=if test $boot_part -eq 0;then " \
"echo Switching to partition 1!;" \
"setenv boot_part 1;" \
"else; " \
"echo Switching to partition 0!;" \
"setenv boot_part 0;" \
"fi;" \
"saveenv;boot\0" \
"ubifsargs=set bootargs ubi.mtd=ubi${boot_part} " \
"root=ubi0:rootfs rootfstype=ubifs\0" \
"kernel=" __stringify(CONFIG_HOSTNAME) "/uImage\0" \
"kernel_fs=/boot/uImage \0" \
"kernel_addr=1000000\0" \
"dtb=" __stringify(CONFIG_HOSTNAME) "/" \
__stringify(CONFIG_HOSTNAME) ".dtb\0" \
"dtb_fs=/boot/" __stringify(CONFIG_HOSTNAME) ".dtb\0" \
"dtb_addr=1800000\0" \
"load_kernel=tftp ${kernel_addr} ${kernel}\0" \
"load_dtb=tftp ${dtb_addr} ${dtb}\0" \
"addip=setenv bootargs ${bootargs} " \
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
":${hostname}:${netdev}:off panic=1\0" \
"addcon=setenv bootargs ${bootargs} console=ttyAMA0," \
"${baudrate}\0" \
"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
"net_nfs=run load_dtb load_kernel; " \
"run nfsargs addip addcon addmtd addmisc;" \
"bootm ${kernel_addr} - ${dtb_addr}\0" \
"mtdids=" MTDIDS_DEFAULT "\0" \
"mtdparts=" MTDPARTS_DEFAULT "\0" \
"nand_ubifs=run ubifs_mount ubifs_load ubifsargs addip" \
" addcon addmisc addmtd;" \
"bootm ${kernel_addr} - ${dtb_addr}\0" \
"ubifs_mount=ubi part ubi${boot_part};ubifsmount ubi:rootfs\0" \
"ubifs_load=ubifsload ${kernel_addr} ${kernel_fs};" \
"ubifsload ${dtb_addr} ${dtb_fs};\0" \
"nand_ubifs=run ubifs_mount ubifs_load ubifsargs addip addcon " \
"addmtd addmisc;bootm ${kernel_addr} - ${dtb_addr}\0" \
"bootcmd=run nand_ubifs\0" \
"\0"
/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM_1 0x00000000
#define PHYS_SDRAM_1_MAXSIZE 0x40000000
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
#define CONFIG_SRAM_BASE 0xd2800000
/* Preserve the last 2 lwords for the boot-counter */
#define CONFIG_SRAM_SIZE ((8 << 10) - 0x8)
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SRAM_BASE
#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SRAM_SIZE
#define CONFIG_SYS_INIT_SP_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
/*
* SPL related defines
*/
#define CONFIG_SPL_TEXT_BASE 0xd2800b00
#define CONFIG_SPL_MAX_SIZE (CONFIG_SRAM_SIZE - 0xb00)
#define CONFIG_SPL_START_S_PATH "arch/arm/cpu/arm926ejs/spear"
#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/arm926ejs/spear/u-boot-spl.lds"
#define CONFIG_SPL_FRAMEWORK
/*
* Please select/define only one of the following
* Each definition corresponds to a supported DDR chip.
* DDR configuration is based on the following selection
*/
#define CONFIG_DDR_MT47H64M16 1
#define CONFIG_DDR_MT47H32M16 0
#define CONFIG_DDR_MT47H128M8 0
/*
* Synchronous/Asynchronous operation of DDR
*
* Select CONFIG_DDR_2HCLK for DDR clk = 333MHz, synchronous operation
* Select CONFIG_DDR_HCLK for DDR clk = 166MHz, synchronous operation
* Select CONFIG_DDR_PLL2 for DDR clk = PLL2, asynchronous operation
*/
#define CONFIG_DDR_2HCLK 1
#define CONFIG_DDR_HCLK 0
#define CONFIG_DDR_PLL2 0
/*
* xxx_BOOT_SUPPORTED macro defines whether a booting type is supported
* or not. Modify/Add to only these macros to define new boot types
*/
#define USB_BOOT_SUPPORTED 0
#define PCIE_BOOT_SUPPORTED 0
#define SNOR_BOOT_SUPPORTED 1
#define NAND_BOOT_SUPPORTED 1
#define PNOR_BOOT_SUPPORTED 0
#define TFTP_BOOT_SUPPORTED 0
#define UART_BOOT_SUPPORTED 0
#define SPI_BOOT_SUPPORTED 0
#define I2C_BOOT_SUPPORTED 0
#define MMC_BOOT_SUPPORTED 0
#endif /* __CONFIG_H */