u-boot/arch/arm/include/asm/mach-imx/mxc_i2c.h

106 lines
2.8 KiB
C
Raw Normal View History

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright (C) 2011 Freescale Semiconductor, Inc. All Rights Reserved.
*/
#ifndef __ASM_ARCH_MXC_MXC_I2C_H__
#define __ASM_ARCH_MXC_MXC_I2C_H__
dm: i2c: mxc_i2c: implement i2c_idle_bus Implement i2c_idle_bus in driver, then setup_i2c can be dropped for boards which enable DM_I2C/DM_GPIO/PINCTRL. The i2c_idle_bus force bus idle flow follows setup_i2c in arch/arm/imx-common/i2c-mxv7.c This patch is an implementation following linux kernel patch: " commit 1c4b6c3bcf30d0804db0d0647d8ebeb862c6f7e5 Author: Gao Pan <b54642@freescale.com> Date: Fri Oct 23 20:28:54 2015 +0800 i2c: imx: implement bus recovery Implement bus recovery methods for i2c-imx so we can recover from situations where SCL/SDA are stuck low. Once i2c bus SCL/SDA are stuck low during transfer, config the i2c pinctrl to gpio mode by calling pinctrl sleep set function, and then use GPIO to emulate the i2c protocol to send nine dummy clock to recover i2c device. After recovery, set i2c pinctrl to default group setting. " See Documentation/devicetree/bindings/i2c/i2c-imx.txt for detailed description. 1. Introuduce scl_gpio/sda_gpio/bus in mxc_i2c_bus. 2. Discard the __weak attribute for i2c_idle_bus and implement it, since we have pinctrl driver/driver model gpio driver. We can use device tree, but not let board code to do this. 3. gpio state for mxc_i2c is not a must, but it is recommended. If there is no gpio state, driver will give tips, but not fail. 4. The i2c controller was first probed, default pinctrl state will be used, so when need to use gpio function, need to do "pinctrl_select_state(dev, "gpio")" and after force bus idle, need to switch back "pinctrl_select_state(dev, "default")". This is example about how to use the gpio force bus idle function: " &i2c1 { clock-frequency = <100000>; pinctrl-names = "default", "gpio"; pinctrl-0 = <&pinctrl_i2c1>; pinctrl-1 = <&pinctrl_i2c1_gpio>; scl-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>; sda-gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>; status = "okay"; [....] }; [.....] pinctrl_i2c1_gpio: i2c1grp_gpio { fsl,pins = < MX6UL_PAD_UART4_TX_DATA__GPIO1_IO28 0x1b8b0 MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29 0x1b8b0 >; }; " Signed-off-by: Peng Fan <van.freenix@gmail.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Stefano Babic <sbabic@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: York Sun <york.sun@nxp.com>
2016-03-11 08:47:50 +00:00
#include <asm-generic/gpio.h>
imx: reorganize IMX code as other SOCs Change is consistent with other SOCs and it is in preparation for adding SOMs. SOC's related files are moved from cpu/ to mach-imx/<SOC>. This change is also coherent with the structure in kernel. Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Fabio Estevam <fabio.estevam@nxp.com> CC: Akshay Bhat <akshaybhat@timesys.com> CC: Ken Lin <Ken.Lin@advantech.com.tw> CC: Marek Vasut <marek.vasut@gmail.com> CC: Heiko Schocher <hs@denx.de> CC: "Sébastien Szymanski" <sebastien.szymanski@armadeus.com> CC: Christian Gmeiner <christian.gmeiner@gmail.com> CC: Stefan Roese <sr@denx.de> CC: Patrick Bruenn <p.bruenn@beckhoff.com> CC: Troy Kisky <troy.kisky@boundarydevices.com> CC: Nikita Kiryanov <nikita@compulab.co.il> CC: Otavio Salvador <otavio@ossystems.com.br> CC: "Eric Bénard" <eric@eukrea.com> CC: Jagan Teki <jagan@amarulasolutions.com> CC: Ye Li <ye.li@nxp.com> CC: Peng Fan <peng.fan@nxp.com> CC: Adrian Alonso <adrian.alonso@nxp.com> CC: Alison Wang <b18965@freescale.com> CC: Tim Harvey <tharvey@gateworks.com> CC: Martin Donnelly <martin.donnelly@ge.com> CC: Marcin Niestroj <m.niestroj@grinn-global.com> CC: Lukasz Majewski <lukma@denx.de> CC: Adam Ford <aford173@gmail.com> CC: "Albert ARIBAUD (3ADEV)" <albert.aribaud@3adev.fr> CC: Boris Brezillon <boris.brezillon@free-electrons.com> CC: Soeren Moch <smoch@web.de> CC: Richard Hu <richard.hu@technexion.com> CC: Wig Cheng <wig.cheng@technexion.com> CC: Vanessa Maegima <vanessa.maegima@nxp.com> CC: Max Krummenacher <max.krummenacher@toradex.com> CC: Stefan Agner <stefan.agner@toradex.com> CC: Markus Niebel <Markus.Niebel@tq-group.com> CC: Breno Lima <breno.lima@nxp.com> CC: Francesco Montefoschi <francesco.montefoschi@udoo.org> CC: Jaehoon Chung <jh80.chung@samsung.com> CC: Scott Wood <oss@buserror.net> CC: Joe Hershberger <joe.hershberger@ni.com> CC: Anatolij Gustschin <agust@denx.de> CC: Simon Glass <sjg@chromium.org> CC: "Andrew F. Davis" <afd@ti.com> CC: "Łukasz Majewski" <l.majewski@samsung.com> CC: Patrice Chotard <patrice.chotard@st.com> CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> CC: Hans de Goede <hdegoede@redhat.com> CC: Masahiro Yamada <yamada.masahiro@socionext.com> CC: Stephen Warren <swarren@nvidia.com> CC: Andre Przywara <andre.przywara@arm.com> CC: "Álvaro Fernández Rojas" <noltari@gmail.com> CC: York Sun <york.sun@nxp.com> CC: Xiaoliang Yang <xiaoliang.yang@nxp.com> CC: Chen-Yu Tsai <wens@csie.org> CC: George McCollister <george.mccollister@gmail.com> CC: Sven Ebenfeld <sven.ebenfeld@gmail.com> CC: Filip Brozovic <fbrozovic@gmail.com> CC: Petr Kulhavy <brain@jikos.cz> CC: Eric Nelson <eric@nelint.com> CC: Bai Ping <ping.bai@nxp.com> CC: Anson Huang <Anson.Huang@nxp.com> CC: Sanchayan Maity <maitysanchayan@gmail.com> CC: Lokesh Vutla <lokeshvutla@ti.com> CC: Patrick Delaunay <patrick.delaunay@st.com> CC: Gary Bisson <gary.bisson@boundarydevices.com> CC: Alexander Graf <agraf@suse.de> CC: u-boot@lists.denx.de Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
2017-06-29 08:16:06 +00:00
#include <asm/mach-imx/iomux-v3.h>
#if CONFIG_IS_ENABLED(CLK)
#include <clk.h>
#endif
struct i2c_pin_ctrl {
iomux_v3_cfg_t i2c_mode;
iomux_v3_cfg_t gpio_mode;
unsigned char gp;
unsigned char spare;
};
struct i2c_pads_info {
struct i2c_pin_ctrl scl;
struct i2c_pin_ctrl sda;
};
i2c: mxc: refactor i2c driver and support dm 1. Introduce a new structure `struct mxc_i2c_bus`, this structure will used for non-DM and DM. 2. Remove `struct mxc_i2c_regs` structure, but use register offset to access registers based on `base` entry of `struct mxc_i2c_bus`. 3. Remove most `#ifdef I2C_QUIRK_REG`. Using driver_data to contain platform flags. A new flag is introduced, I2C_QUIRK_FLAG. 4. Most functions use `struct mxc_i2c_bus` as one of the parameters. Make most functions common to DM and non-DM, try to avoid duplicated code. 5. Support DM, but pinctrl is not included. Pinmux setting is still set by setup_i2c, but we do not need bus_i2c_init for DM. 6. struct i2c_parms and struct sram_data are removed. 7. Remove bus_i2c_read bus_i2c_write prototype in header file. The frist paramter of bus_i2c_init is modified to i2c index. Add new prototype i2c_idle_bus and force_bus_idle. Since bus_i2c_init is not good for DM I2C and pinctrl is missed, we use a weak function for i2c_idle_bus. Board file take the responsibility to implement this function, like this: " int i2c_idle_bus(struct mxc_i2c_bus *i2c_bus) { if (i2c_bus->index == 0) force_bus_idle(i2c_pads_info0); else if (i2c_bus->index == 1) force_bus_idle(i2c_pads_info1); else xxxxxx } " 8. Introduce a weak function, enable_i2c_clk 9. Tested on an i.MX7 platform. Log info: => dm tree Class Probed Name ---------------------------------------- root [ + ] root_driver simple_bus [ ] |-- soc simple_bus [ ] | |-- aips-bus@30000000 simple_bus [ ] | | |-- anatop@30360000 simple_bus [ ] | | `-- snvs@30370000 simple_bus [ ] | |-- aips-bus@30400000 simple_bus [ ] | `-- aips-bus@30800000 i2c [ ] | |-- i2c@30a20000 i2c [ ] | `-- i2c@30a40000 simple_bus [ ] `-- regulators => i2c dev 0 Setting bus to 0 => i2c probe Valid chip addresses: 08 50 => i2c md 8 31 0031: 08 08 08 08 08 08 08 08 08 08 08 08 08 08 08 08 Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Acked-by: Simon Glass <sjg@chromium.org>
2015-05-14 23:29:12 +00:00
/*
* Information about i2c controller
* struct mxc_i2c_bus - information about the i2c[x] bus
* @index: i2c bus index
* @base: Address of I2C bus controller
* @driver_data: Flags for different platforms, such as I2C_QUIRK_FLAG.
* @speed: Speed of I2C bus
* @pads_info: pinctrl info for this i2c bus, will be used when pinctrl is ok.
* The following two is only to be compatible with non-DM part.
* @idle_bus_fn: function to force bus idle
* @idle_bus_data: parameter for idle_bus_fun
dm: i2c: mxc_i2c: implement i2c_idle_bus Implement i2c_idle_bus in driver, then setup_i2c can be dropped for boards which enable DM_I2C/DM_GPIO/PINCTRL. The i2c_idle_bus force bus idle flow follows setup_i2c in arch/arm/imx-common/i2c-mxv7.c This patch is an implementation following linux kernel patch: " commit 1c4b6c3bcf30d0804db0d0647d8ebeb862c6f7e5 Author: Gao Pan <b54642@freescale.com> Date: Fri Oct 23 20:28:54 2015 +0800 i2c: imx: implement bus recovery Implement bus recovery methods for i2c-imx so we can recover from situations where SCL/SDA are stuck low. Once i2c bus SCL/SDA are stuck low during transfer, config the i2c pinctrl to gpio mode by calling pinctrl sleep set function, and then use GPIO to emulate the i2c protocol to send nine dummy clock to recover i2c device. After recovery, set i2c pinctrl to default group setting. " See Documentation/devicetree/bindings/i2c/i2c-imx.txt for detailed description. 1. Introuduce scl_gpio/sda_gpio/bus in mxc_i2c_bus. 2. Discard the __weak attribute for i2c_idle_bus and implement it, since we have pinctrl driver/driver model gpio driver. We can use device tree, but not let board code to do this. 3. gpio state for mxc_i2c is not a must, but it is recommended. If there is no gpio state, driver will give tips, but not fail. 4. The i2c controller was first probed, default pinctrl state will be used, so when need to use gpio function, need to do "pinctrl_select_state(dev, "gpio")" and after force bus idle, need to switch back "pinctrl_select_state(dev, "default")". This is example about how to use the gpio force bus idle function: " &i2c1 { clock-frequency = <100000>; pinctrl-names = "default", "gpio"; pinctrl-0 = <&pinctrl_i2c1>; pinctrl-1 = <&pinctrl_i2c1_gpio>; scl-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>; sda-gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>; status = "okay"; [....] }; [.....] pinctrl_i2c1_gpio: i2c1grp_gpio { fsl,pins = < MX6UL_PAD_UART4_TX_DATA__GPIO1_IO28 0x1b8b0 MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29 0x1b8b0 >; }; " Signed-off-by: Peng Fan <van.freenix@gmail.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Stefano Babic <sbabic@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: York Sun <york.sun@nxp.com>
2016-03-11 08:47:50 +00:00
* For DM:
* bus: The device structure for i2c bus controller
* scl-gpio: specify the gpio related to SCL pin
* sda-gpio: specify the gpio related to SDA pin
i2c: mxc: refactor i2c driver and support dm 1. Introduce a new structure `struct mxc_i2c_bus`, this structure will used for non-DM and DM. 2. Remove `struct mxc_i2c_regs` structure, but use register offset to access registers based on `base` entry of `struct mxc_i2c_bus`. 3. Remove most `#ifdef I2C_QUIRK_REG`. Using driver_data to contain platform flags. A new flag is introduced, I2C_QUIRK_FLAG. 4. Most functions use `struct mxc_i2c_bus` as one of the parameters. Make most functions common to DM and non-DM, try to avoid duplicated code. 5. Support DM, but pinctrl is not included. Pinmux setting is still set by setup_i2c, but we do not need bus_i2c_init for DM. 6. struct i2c_parms and struct sram_data are removed. 7. Remove bus_i2c_read bus_i2c_write prototype in header file. The frist paramter of bus_i2c_init is modified to i2c index. Add new prototype i2c_idle_bus and force_bus_idle. Since bus_i2c_init is not good for DM I2C and pinctrl is missed, we use a weak function for i2c_idle_bus. Board file take the responsibility to implement this function, like this: " int i2c_idle_bus(struct mxc_i2c_bus *i2c_bus) { if (i2c_bus->index == 0) force_bus_idle(i2c_pads_info0); else if (i2c_bus->index == 1) force_bus_idle(i2c_pads_info1); else xxxxxx } " 8. Introduce a weak function, enable_i2c_clk 9. Tested on an i.MX7 platform. Log info: => dm tree Class Probed Name ---------------------------------------- root [ + ] root_driver simple_bus [ ] |-- soc simple_bus [ ] | |-- aips-bus@30000000 simple_bus [ ] | | |-- anatop@30360000 simple_bus [ ] | | `-- snvs@30370000 simple_bus [ ] | |-- aips-bus@30400000 simple_bus [ ] | `-- aips-bus@30800000 i2c [ ] | |-- i2c@30a20000 i2c [ ] | `-- i2c@30a40000 simple_bus [ ] `-- regulators => i2c dev 0 Setting bus to 0 => i2c probe Valid chip addresses: 08 50 => i2c md 8 31 0031: 08 08 08 08 08 08 08 08 08 08 08 08 08 08 08 08 Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Acked-by: Simon Glass <sjg@chromium.org>
2015-05-14 23:29:12 +00:00
*/
struct mxc_i2c_bus {
/*
* board file can use this index to locate which i2c_pads_info is for
* i2c_idle_bus. When pinmux is implement, this entry can be
* discarded. Here we do not use dev->seq, because we do not want to
* export device to board file.
*/
int index;
ulong base;
ulong driver_data;
int speed;
struct i2c_pads_info *pads_info;
#if CONFIG_IS_ENABLED(CLK)
struct clk per_clk;
#endif
i2c: mxc: refactor i2c driver and support dm 1. Introduce a new structure `struct mxc_i2c_bus`, this structure will used for non-DM and DM. 2. Remove `struct mxc_i2c_regs` structure, but use register offset to access registers based on `base` entry of `struct mxc_i2c_bus`. 3. Remove most `#ifdef I2C_QUIRK_REG`. Using driver_data to contain platform flags. A new flag is introduced, I2C_QUIRK_FLAG. 4. Most functions use `struct mxc_i2c_bus` as one of the parameters. Make most functions common to DM and non-DM, try to avoid duplicated code. 5. Support DM, but pinctrl is not included. Pinmux setting is still set by setup_i2c, but we do not need bus_i2c_init for DM. 6. struct i2c_parms and struct sram_data are removed. 7. Remove bus_i2c_read bus_i2c_write prototype in header file. The frist paramter of bus_i2c_init is modified to i2c index. Add new prototype i2c_idle_bus and force_bus_idle. Since bus_i2c_init is not good for DM I2C and pinctrl is missed, we use a weak function for i2c_idle_bus. Board file take the responsibility to implement this function, like this: " int i2c_idle_bus(struct mxc_i2c_bus *i2c_bus) { if (i2c_bus->index == 0) force_bus_idle(i2c_pads_info0); else if (i2c_bus->index == 1) force_bus_idle(i2c_pads_info1); else xxxxxx } " 8. Introduce a weak function, enable_i2c_clk 9. Tested on an i.MX7 platform. Log info: => dm tree Class Probed Name ---------------------------------------- root [ + ] root_driver simple_bus [ ] |-- soc simple_bus [ ] | |-- aips-bus@30000000 simple_bus [ ] | | |-- anatop@30360000 simple_bus [ ] | | `-- snvs@30370000 simple_bus [ ] | |-- aips-bus@30400000 simple_bus [ ] | `-- aips-bus@30800000 i2c [ ] | |-- i2c@30a20000 i2c [ ] | `-- i2c@30a40000 simple_bus [ ] `-- regulators => i2c dev 0 Setting bus to 0 => i2c probe Valid chip addresses: 08 50 => i2c md 8 31 0031: 08 08 08 08 08 08 08 08 08 08 08 08 08 08 08 08 Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Acked-by: Simon Glass <sjg@chromium.org>
2015-05-14 23:29:12 +00:00
#ifndef CONFIG_DM_I2C
int (*idle_bus_fn)(void *p);
void *idle_bus_data;
dm: i2c: mxc_i2c: implement i2c_idle_bus Implement i2c_idle_bus in driver, then setup_i2c can be dropped for boards which enable DM_I2C/DM_GPIO/PINCTRL. The i2c_idle_bus force bus idle flow follows setup_i2c in arch/arm/imx-common/i2c-mxv7.c This patch is an implementation following linux kernel patch: " commit 1c4b6c3bcf30d0804db0d0647d8ebeb862c6f7e5 Author: Gao Pan <b54642@freescale.com> Date: Fri Oct 23 20:28:54 2015 +0800 i2c: imx: implement bus recovery Implement bus recovery methods for i2c-imx so we can recover from situations where SCL/SDA are stuck low. Once i2c bus SCL/SDA are stuck low during transfer, config the i2c pinctrl to gpio mode by calling pinctrl sleep set function, and then use GPIO to emulate the i2c protocol to send nine dummy clock to recover i2c device. After recovery, set i2c pinctrl to default group setting. " See Documentation/devicetree/bindings/i2c/i2c-imx.txt for detailed description. 1. Introuduce scl_gpio/sda_gpio/bus in mxc_i2c_bus. 2. Discard the __weak attribute for i2c_idle_bus and implement it, since we have pinctrl driver/driver model gpio driver. We can use device tree, but not let board code to do this. 3. gpio state for mxc_i2c is not a must, but it is recommended. If there is no gpio state, driver will give tips, but not fail. 4. The i2c controller was first probed, default pinctrl state will be used, so when need to use gpio function, need to do "pinctrl_select_state(dev, "gpio")" and after force bus idle, need to switch back "pinctrl_select_state(dev, "default")". This is example about how to use the gpio force bus idle function: " &i2c1 { clock-frequency = <100000>; pinctrl-names = "default", "gpio"; pinctrl-0 = <&pinctrl_i2c1>; pinctrl-1 = <&pinctrl_i2c1_gpio>; scl-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>; sda-gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>; status = "okay"; [....] }; [.....] pinctrl_i2c1_gpio: i2c1grp_gpio { fsl,pins = < MX6UL_PAD_UART4_TX_DATA__GPIO1_IO28 0x1b8b0 MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29 0x1b8b0 >; }; " Signed-off-by: Peng Fan <van.freenix@gmail.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Stefano Babic <sbabic@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: York Sun <york.sun@nxp.com>
2016-03-11 08:47:50 +00:00
#else
struct udevice *bus;
/* Use gpio to force bus idle when bus state is abnormal */
struct gpio_desc scl_gpio;
struct gpio_desc sda_gpio;
i2c: mxc: refactor i2c driver and support dm 1. Introduce a new structure `struct mxc_i2c_bus`, this structure will used for non-DM and DM. 2. Remove `struct mxc_i2c_regs` structure, but use register offset to access registers based on `base` entry of `struct mxc_i2c_bus`. 3. Remove most `#ifdef I2C_QUIRK_REG`. Using driver_data to contain platform flags. A new flag is introduced, I2C_QUIRK_FLAG. 4. Most functions use `struct mxc_i2c_bus` as one of the parameters. Make most functions common to DM and non-DM, try to avoid duplicated code. 5. Support DM, but pinctrl is not included. Pinmux setting is still set by setup_i2c, but we do not need bus_i2c_init for DM. 6. struct i2c_parms and struct sram_data are removed. 7. Remove bus_i2c_read bus_i2c_write prototype in header file. The frist paramter of bus_i2c_init is modified to i2c index. Add new prototype i2c_idle_bus and force_bus_idle. Since bus_i2c_init is not good for DM I2C and pinctrl is missed, we use a weak function for i2c_idle_bus. Board file take the responsibility to implement this function, like this: " int i2c_idle_bus(struct mxc_i2c_bus *i2c_bus) { if (i2c_bus->index == 0) force_bus_idle(i2c_pads_info0); else if (i2c_bus->index == 1) force_bus_idle(i2c_pads_info1); else xxxxxx } " 8. Introduce a weak function, enable_i2c_clk 9. Tested on an i.MX7 platform. Log info: => dm tree Class Probed Name ---------------------------------------- root [ + ] root_driver simple_bus [ ] |-- soc simple_bus [ ] | |-- aips-bus@30000000 simple_bus [ ] | | |-- anatop@30360000 simple_bus [ ] | | `-- snvs@30370000 simple_bus [ ] | |-- aips-bus@30400000 simple_bus [ ] | `-- aips-bus@30800000 i2c [ ] | |-- i2c@30a20000 i2c [ ] | `-- i2c@30a40000 simple_bus [ ] `-- regulators => i2c dev 0 Setting bus to 0 => i2c probe Valid chip addresses: 08 50 => i2c md 8 31 0031: 08 08 08 08 08 08 08 08 08 08 08 08 08 08 08 08 Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Acked-by: Simon Glass <sjg@chromium.org>
2015-05-14 23:29:12 +00:00
#endif
};
#if defined(CONFIG_MX6QDL)
#define I2C_PADS(name, scl_i2c, scl_gpio, scl_gp, sda_i2c, sda_gpio, sda_gp) \
struct i2c_pads_info mx6q_##name = { \
.scl = { \
.i2c_mode = MX6Q_##scl_i2c, \
.gpio_mode = MX6Q_##scl_gpio, \
.gp = scl_gp, \
}, \
.sda = { \
.i2c_mode = MX6Q_##sda_i2c, \
.gpio_mode = MX6Q_##sda_gpio, \
.gp = sda_gp, \
} \
}; \
struct i2c_pads_info mx6s_##name = { \
.scl = { \
.i2c_mode = MX6DL_##scl_i2c, \
.gpio_mode = MX6DL_##scl_gpio, \
.gp = scl_gp, \
}, \
.sda = { \
.i2c_mode = MX6DL_##sda_i2c, \
.gpio_mode = MX6DL_##sda_gpio, \
.gp = sda_gp, \
} \
};
#define I2C_PADS_INFO(name) \
(is_mx6dq() || is_mx6dqp()) ? &mx6q_##name : &mx6s_##name
#endif
int setup_i2c(unsigned i2c_index, int speed, int slave_addr,
struct i2c_pads_info *p);
i2c: mxc: refactor i2c driver and support dm 1. Introduce a new structure `struct mxc_i2c_bus`, this structure will used for non-DM and DM. 2. Remove `struct mxc_i2c_regs` structure, but use register offset to access registers based on `base` entry of `struct mxc_i2c_bus`. 3. Remove most `#ifdef I2C_QUIRK_REG`. Using driver_data to contain platform flags. A new flag is introduced, I2C_QUIRK_FLAG. 4. Most functions use `struct mxc_i2c_bus` as one of the parameters. Make most functions common to DM and non-DM, try to avoid duplicated code. 5. Support DM, but pinctrl is not included. Pinmux setting is still set by setup_i2c, but we do not need bus_i2c_init for DM. 6. struct i2c_parms and struct sram_data are removed. 7. Remove bus_i2c_read bus_i2c_write prototype in header file. The frist paramter of bus_i2c_init is modified to i2c index. Add new prototype i2c_idle_bus and force_bus_idle. Since bus_i2c_init is not good for DM I2C and pinctrl is missed, we use a weak function for i2c_idle_bus. Board file take the responsibility to implement this function, like this: " int i2c_idle_bus(struct mxc_i2c_bus *i2c_bus) { if (i2c_bus->index == 0) force_bus_idle(i2c_pads_info0); else if (i2c_bus->index == 1) force_bus_idle(i2c_pads_info1); else xxxxxx } " 8. Introduce a weak function, enable_i2c_clk 9. Tested on an i.MX7 platform. Log info: => dm tree Class Probed Name ---------------------------------------- root [ + ] root_driver simple_bus [ ] |-- soc simple_bus [ ] | |-- aips-bus@30000000 simple_bus [ ] | | |-- anatop@30360000 simple_bus [ ] | | `-- snvs@30370000 simple_bus [ ] | |-- aips-bus@30400000 simple_bus [ ] | `-- aips-bus@30800000 i2c [ ] | |-- i2c@30a20000 i2c [ ] | `-- i2c@30a40000 simple_bus [ ] `-- regulators => i2c dev 0 Setting bus to 0 => i2c probe Valid chip addresses: 08 50 => i2c md 8 31 0031: 08 08 08 08 08 08 08 08 08 08 08 08 08 08 08 08 Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Acked-by: Simon Glass <sjg@chromium.org>
2015-05-14 23:29:12 +00:00
void bus_i2c_init(int index, int speed, int slave_addr,
int (*idle_bus_fn)(void *p), void *p);
i2c: mxc: refactor i2c driver and support dm 1. Introduce a new structure `struct mxc_i2c_bus`, this structure will used for non-DM and DM. 2. Remove `struct mxc_i2c_regs` structure, but use register offset to access registers based on `base` entry of `struct mxc_i2c_bus`. 3. Remove most `#ifdef I2C_QUIRK_REG`. Using driver_data to contain platform flags. A new flag is introduced, I2C_QUIRK_FLAG. 4. Most functions use `struct mxc_i2c_bus` as one of the parameters. Make most functions common to DM and non-DM, try to avoid duplicated code. 5. Support DM, but pinctrl is not included. Pinmux setting is still set by setup_i2c, but we do not need bus_i2c_init for DM. 6. struct i2c_parms and struct sram_data are removed. 7. Remove bus_i2c_read bus_i2c_write prototype in header file. The frist paramter of bus_i2c_init is modified to i2c index. Add new prototype i2c_idle_bus and force_bus_idle. Since bus_i2c_init is not good for DM I2C and pinctrl is missed, we use a weak function for i2c_idle_bus. Board file take the responsibility to implement this function, like this: " int i2c_idle_bus(struct mxc_i2c_bus *i2c_bus) { if (i2c_bus->index == 0) force_bus_idle(i2c_pads_info0); else if (i2c_bus->index == 1) force_bus_idle(i2c_pads_info1); else xxxxxx } " 8. Introduce a weak function, enable_i2c_clk 9. Tested on an i.MX7 platform. Log info: => dm tree Class Probed Name ---------------------------------------- root [ + ] root_driver simple_bus [ ] |-- soc simple_bus [ ] | |-- aips-bus@30000000 simple_bus [ ] | | |-- anatop@30360000 simple_bus [ ] | | `-- snvs@30370000 simple_bus [ ] | |-- aips-bus@30400000 simple_bus [ ] | `-- aips-bus@30800000 i2c [ ] | |-- i2c@30a20000 i2c [ ] | `-- i2c@30a40000 simple_bus [ ] `-- regulators => i2c dev 0 Setting bus to 0 => i2c probe Valid chip addresses: 08 50 => i2c md 8 31 0031: 08 08 08 08 08 08 08 08 08 08 08 08 08 08 08 08 Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Acked-by: Simon Glass <sjg@chromium.org>
2015-05-14 23:29:12 +00:00
int force_idle_bus(void *priv);
int i2c_idle_bus(struct mxc_i2c_bus *i2c_bus);
#endif