u-boot/configs/ls1046aqds_sdcard_ifc_defconfig

140 lines
4.1 KiB
Text
Raw Normal View History

CONFIG_ARM=y
CONFIG_COUNTER_FREQUENCY=25000000
CONFIG_TARGET_LS1046AQDS=y
CONFIG_TEXT_BASE=0x82000000
CONFIG_SYS_MALLOC_LEN=0x102000
CONFIG_SPL_LIBCOMMON_SUPPORT=y
CONFIG_SPL_LIBGENERIC_SUPPORT=y
CONFIG_NR_DRAM_BANKS=2
CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0
CONFIG_ENV_SIZE=0x2000
CONFIG_ENV_OFFSET=0x300000
CONFIG_SYS_I2C_MXC_I2C1=y
CONFIG_SYS_I2C_MXC_I2C2=y
CONFIG_SYS_I2C_MXC_I2C3=y
CONFIG_SYS_I2C_MXC_I2C4=y
CONFIG_DM_GPIO=y
CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1046a-qds-duart"
CONFIG_SPL_TEXT_BASE=0x10000000
CONFIG_FSL_LS_PPA=y
CONFIG_SPL_MMC=y
CONFIG_SPL_SERIAL=y
CONFIG_SPL_DRIVERS_MISC=y
CONFIG_SPL_STACK=0x10020000
CONFIG_SPL=y
CONFIG_AHCI=y
CONFIG_LAYERSCAPE_NS_ACCESS=y
CONFIG_PCIE1=y
CONFIG_PCIE2=y
CONFIG_PCIE3=y
CONFIG_FSL_USE_PCA9547_MUX=y
CONFIG_VID=y
CONFIG_VID_FLS_ENV="ls1046aqds_vdd_mv"
CONFIG_VOL_MONITOR_INA220=y
CONFIG_VOL_MONITOR_IR36021_SET=y
CONFIG_FSL_QIXIS=y
# CONFIG_QIXIS_I2C_ACCESS is not set
CONFIG_SYS_MEMTEST_START=0x80000000
CONFIG_SYS_MEMTEST_END=0x9fffffff
CONFIG_REMAKE_ELF=y
CONFIG_SYS_MONITOR_LEN=1048576
CONFIG_MP=y
CONFIG_FIT_VERBOSE=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_DYNAMIC_SYS_CLK_FREQ=y
CONFIG_RAMBOOT_PBL=y
CONFIG_SYS_FSL_PBL_PBI="board/freescale/ls1046aqds/ls1046aqds_pbi.cfg"
CONFIG_SYS_FSL_PBL_RCW="board/freescale/ls1046aqds/ls1046aqds_rcw_sd_ifc.cfg"
CONFIG_DISTRO_DEFAULTS=y
CONFIG_SD_BOOT=y
CONFIG_BOOTDELAY=10
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 mtdparts=60000000.nor:2m@0x100000(nor_bank0_uboot),40m@0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m@0x4100000(nor_bank4_uboot),40m@0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:4m(nand_uboot),36m(nand_kernel),472m(nand_free);spi0.0:2m(uboot),14m(free)"
CONFIG_BOOTCOMMAND="run distro_bootcmd; run sd_bootcmd; env exists secureboot && esbc_halt;;"
CONFIG_ARCH_MISC_INIT=y
CONFIG_MISC_INIT_R=y
CONFIG_SPL_MAX_SIZE=0x1f000
CONFIG_SPL_PAD_TO=0x21000
CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
CONFIG_SPL_BSS_START_ADDR=0x8f000000
CONFIG_SPL_BSS_MAX_SIZE=0x80000
CONFIG_SPL_FSL_PBL=y
CONFIG_SPL_BOARD_INIT=y
# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
CONFIG_SYS_SPL_MALLOC=y
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x110
CONFIG_SPL_ENV_SUPPORT=y
CONFIG_SPL_I2C=y
CONFIG_SPL_MPC8XXX_INIT_DDR=y
CONFIG_SPL_WATCHDOG=y
CONFIG_SYS_MAXARGS=64
CONFIG_SYS_PBSIZE=532
CONFIG_CMD_BOOTZ=y
CONFIG_CMD_IMLS=y
CONFIG_CMD_GREPENV=y
CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
CONFIG_CMD_MEMINFO=y
CONFIG_CMD_MEMTEST=y
CONFIG_CMD_GPIO=y
CONFIG_CMD_GPT=y
CONFIG_CMD_I2C=y
CONFIG_CMD_MMC=y
CONFIG_CMD_NAND=y
CONFIG_CMD_PCI=y
CONFIG_CMD_USB=y
CONFIG_CMD_CACHE=y
CONFIG_MTDPARTS_DEFAULT="mtdparts=60000000.nor:2m@0x100000(nor_bank0_uboot),40m@0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m@0x4100000(nor_bank4_uboot),40m@0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:4m(nand_uboot),36m(nand_kernel),472m(nand_free);spi0.0:2m(uboot),14m(free)"
# CONFIG_SPL_EFI_PARTITION is not set
CONFIG_OF_CONTROL=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_SATA=y
CONFIG_SATA_CEVA=y
CONFIG_FSL_CAAM=y
CONFIG_DYNAMIC_DDR_CLK_FREQ=y
CONFIG_DDR_ECC=y
CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y
CONFIG_MPC8XXX_GPIO=y
CONFIG_DM_I2C=y
CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
CONFIG_SYS_I2C_EEPROM_ADDR=0x57
CONFIG_FSL_ESDHC=y
CONFIG_MTD=y
flash: complete CONFIG_SYS_NO_FLASH move with renaming We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is not completed. Finish this work by the tool. During this move, let's rename it to CONFIG_MTD_NOR_FLASH. Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH" than those of "#ifdef CONFIG_SYS_NO_FLASH". Flipping the logic will make the code more readable. Besides, negative meaning symbols do not fit in obj-$(CONFIG_...) style Makefiles. This commit was created as follows: [1] Edit "default n" to "default y" in the config entry in common/Kconfig. [2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH" [3] Rename the instances in defconfigs by the following: find . -path './configs/*_defconfig' | xargs sed -i \ -e '/CONFIG_SYS_NO_FLASH=y/d' \ -e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/' [4] Change the conditionals by the following: find . -name '*.[ch]' | xargs sed -i \ -e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \ -e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \ -e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \ -e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/' [5] Modify the following manually - Rename the rest of instances - Remove the description from README - Create the new Kconfig entry in drivers/mtd/Kconfig - Remove the old Kconfig entry from common/Kconfig - Remove the garbage comments from include/configs/*.h Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-02-11 13:43:54 +00:00
CONFIG_MTD_NOR_FLASH=y
CONFIG_FLASH_CFI_DRIVER=y
CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS=y
CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
CONFIG_SYS_FLASH_EMPTY_INFO=y
CONFIG_SYS_FLASH_CFI=y
CONFIG_SYS_FLASH_QUIET_TEST=y
CONFIG_SYS_MAX_FLASH_SECT=1024
CONFIG_SYS_MAX_FLASH_BANKS=2
CONFIG_MTD_RAW_NAND=y
CONFIG_NAND_FSL_IFC=y
CONFIG_SYS_NAND_ONFI_DETECTION=y
CONFIG_SF_DEFAULT_BUS=1
CONFIG_SPI_FLASH_EON=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_SPI_FLASH_SST=y
CONFIG_PHYLIB=y
CONFIG_PHYLIB_10G=y
CONFIG_PHY_REALTEK=y
CONFIG_PHY_VITESSE=y
CONFIG_E1000=y
CONFIG_NVME_PCI=y
CONFIG_PCI=y
CONFIG_DM_PCI_COMPAT=y
CONFIG_PCIE_LAYERSCAPE_RC=y
CONFIG_PCIE_LAYERSCAPE_EP=y
CONFIG_DM_SCSI=y
CONFIG_SYS_NS16550_SERIAL=y
CONFIG_SPI=y
CONFIG_DM_SPI=y
CONFIG_FSL_DSPI=y
CONFIG_USB=y
CONFIG_USB_XHCI_HCD=y
CONFIG_USB_XHCI_DWC3=y