u-boot/arch/arm/mach-mvebu/Makefile

75 lines
1.8 KiB
Makefile
Raw Normal View History

# SPDX-License-Identifier: GPL-2.0+
#
# Copyright (C) 2014-2016 Stefan Roese <sr@denx.de>
ifdef CONFIG_ARM64
obj-$(CONFIG_ARMADA_3700) += armada3700/
arm64: mvebu: Add basic support for the Marvell Armada 7K/8K SoC Compared to the Armada 3700, the Armada 7K and 8K are much more on the high-end side: they use a dual Cortex-A72 or a quad Cortex-A72, as opposed to the Cortex-A53 for the Armada 3700. The Armada 7K and 8K also use a fairly unique architecture, internally they are composed of several components: - One AP (Application Processor), which contains the processor itself and a few core hardware blocks. The AP used in the Armada 7K and 8K is called AP806, and is available in two configurations: dual Cortex-A72 and quad Cortex-A72. - One or two CP (Communication Processor), which contain most of the I/O interfaces (SATA, PCIe, Ethernet, etc.). The 7K family chips have one CP, while the 8K family chips integrate two CPs, providing two times the number of I/O interfaces available in the CP. The CP used in the 7K and 8K is called CP110. All in all, this gives the following combinations: - Armada 7020, which is a dual Cortex-A72 with one CP - Armada 7040, which is a quad Cortex-A72 with one CP - Armada 8020, which is a dual Cortex-A72 with two CPs - Armada 8040, which is a quad Cortex-A72 with two CPs This patch adds basic support for this ARMv8 based SoC into U-Boot. Future patches will integrate other device drivers and board support, starting with the Marvell DB-88F7040 development board. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Nadav Haklai <nadavh@marvell.com> Cc: Neta Zur Hershkovits <neta@marvell.com> Cc: Kostya Porotchkin <kostap@marvell.com> Cc: Omri Itach <omrii@marvell.com> Cc: Igal Liberman <igall@marvell.com> Cc: Haim Boot <hayim@marvell.com> Cc: Hanna Hawa <hannah@marvell.com>
2016-05-25 06:13:45 +00:00
obj-$(CONFIG_ARMADA_8K) += armada8k/
obj-y += arm64-common.o
else # CONFIG_ARM64
ifdef CONFIG_KIRKWOOD
obj-y = dram.o
obj-y += gpio.o
obj-y += mbus.o
obj-y += timer.o
else # CONFIG_KIRKWOOD
obj-y = cpu.o
obj-y += dram.o
ifndef CONFIG_SPL_BUILD
obj-$(CONFIG_ARMADA_375) += ../../../drivers/ddr/marvell/axp/xor.o
obj-$(CONFIG_ARMADA_38X) += ../../../drivers/ddr/marvell/a38x/xor.o
obj-$(CONFIG_ARMADA_XP) += ../../../drivers/ddr/marvell/axp/xor.o
obj-$(CONFIG_ARMADA_MSYS) += ../../../drivers/ddr/marvell/axp/xor.o
obj-$(CONFIG_MVEBU_EFUSE) += efuse.o
extra-y += kwbimage.cfg
KWB_REPLACE += BOOT_FROM
ifneq ($(CONFIG_MVEBU_SPL_BOOT_DEVICE_SPI),)
KWB_CFG_BOOT_FROM=spi
endif
ifneq ($(CONFIG_MVEBU_SPL_BOOT_DEVICE_MMC),)
KWB_CFG_BOOT_FROM=sdio
endif
ifneq ($(CONFIG_MVEBU_SPL_BOOT_DEVICE_UART),)
KWB_CFG_BOOT_FROM=uart
endif
ifneq ($(CONFIG_SECURED_MODE_IMAGE),)
KWB_REPLACE += CSK_INDEX
KWB_CFG_CSK_INDEX = $(CONFIG_SECURED_MODE_CSK_INDEX)
KWB_REPLACE += SEC_BOOT_DEV
KWB_CFG_SEC_BOOT_DEV=$(patsubst "%",%, \
$(if $(findstring BOOT_SPI_NOR_FLASH,$(CONFIG_SPL_BOOT_DEVICE)),0x34) \
$(if $(findstring BOOT_SDIO_MMC_CARD,$(CONFIG_SPL_BOOT_DEVICE)),0x31) \
)
KWB_REPLACE += SEC_FUSE_DUMP
KWB_CFG_SEC_FUSE_DUMP = a38x
endif
$(src)/kwbimage.cfg: $(src)/kwbimage.cfg.in include/autoconf.mk \
include/config/auto.conf
$(Q)sed -ne '$(foreach V,$(KWB_REPLACE),s/^#@$(V)/$(V) $(KWB_CFG_$(V))/;)p' \
<$< >$(dir $<)$(@F)
endif # CONFIG_SPL_BUILD
obj-y += gpio.o
obj-y += mbus.o
obj-y += timer.o
obj-$(CONFIG_SPL_BUILD) += spl.o
obj-$(CONFIG_SPL_BUILD) += lowlevel_spl.o
obj-$(CONFIG_ARMADA_38X) += serdes/a38x/
obj-$(CONFIG_ARMADA_XP) += serdes/axp/
endif # CONFIG_KIRKWOOD
endif # CONFIG_ARM64