u-boot/board/mscc/jr2/jr2.c

126 lines
2.6 KiB
C
Raw Normal View History

// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* Copyright (c) 2018 Microsemi Corporation
*/
#include <common.h>
#include <asm/io.h>
#include <led.h>
enum {
BOARD_TYPE_PCB110 = 0xAABBCE00,
BOARD_TYPE_PCB111,
BOARD_TYPE_PCB112,
};
int board_early_init_r(void)
{
/* Prepare SPI controller to be used in master mode */
writel(0, BASE_CFG + ICPU_SW_MODE);
clrsetbits_le32(BASE_CFG + ICPU_GENERAL_CTRL,
ICPU_GENERAL_CTRL_IF_SI_OWNER_M,
ICPU_GENERAL_CTRL_IF_SI_OWNER(2));
/* Address of boot parameters */
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE;
/* LED setup */
if (IS_ENABLED(CONFIG_LED))
led_default_state();
return 0;
}
static void vcoreiii_gpio_set_alternate(int gpio, int mode)
{
u32 mask;
u32 val0, val1;
void __iomem *reg0, *reg1;
if (gpio < 32) {
mask = BIT(gpio);
reg0 = BASE_DEVCPU_GCB + GPIO_GPIO_ALT(0);
reg1 = BASE_DEVCPU_GCB + GPIO_GPIO_ALT(1);
} else {
gpio -= 32;
mask = BIT(gpio);
reg0 = BASE_DEVCPU_GCB + GPIO_GPIO_ALT1(0);
reg1 = BASE_DEVCPU_GCB + GPIO_GPIO_ALT1(1);
}
val0 = readl(reg0);
val1 = readl(reg1);
if (mode == 1) {
writel(val0 | mask, reg0);
writel(val1 & ~mask, reg1);
} else if (mode == 2) {
writel(val0 & ~mask, reg0);
writel(val1 | mask, reg1);
} else if (mode == 3) {
writel(val0 | mask, reg0);
writel(val1 | mask, reg1);
} else {
writel(val0 & ~mask, reg0);
writel(val1 & ~mask, reg1);
}
}
void board_debug_uart_init(void)
{
/* too early for the pinctrl driver, so configure the UART pins here */
vcoreiii_gpio_set_alternate(10, 1);
vcoreiii_gpio_set_alternate(11, 1);
}
static void do_board_detect(void)
{
int i;
u16 pval;
/* MIIM 1 + 2 MDC/MDIO */
for (i = 56; i < 60; i++)
vcoreiii_gpio_set_alternate(i, 1);
/* small delay for settling the pins */
mdelay(30);
if (mscc_phy_rd(0, 0x10, 0x3, &pval) == 0 &&
((pval >> 4) & 0x3F) == 0x3c) {
gd->board_type = BOARD_TYPE_PCB112; /* Serval2-NID */
} else if (mscc_phy_rd(1, 0x0, 0x3, &pval) == 0 &&
((pval >> 4) & 0x3F) == 0x3c) {
gd->board_type = BOARD_TYPE_PCB110; /* Jr2-24 */
} else {
/* Fall-back */
gd->board_type = BOARD_TYPE_PCB111; /* Jr2-48 */
}
}
#if defined(CONFIG_MULTI_DTB_FIT)
int board_fit_config_name_match(const char *name)
{
if (gd->board_type == BOARD_TYPE_PCB110 &&
strcmp(name, "jr2_pcb110") == 0)
return 0;
if (gd->board_type == BOARD_TYPE_PCB111 &&
strcmp(name, "jr2_pcb111") == 0)
return 0;
if (gd->board_type == BOARD_TYPE_PCB112 &&
strcmp(name, "serval2_pcb112") == 0)
return 0;
return -1;
}
#endif
#if defined(CONFIG_DTB_RESELECT)
int embedded_dtb_select(void)
{
do_board_detect();
fdtdec_setup();
return 0;
}
#endif