u-boot/configs/ga10h_v1_1_defconfig

CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
CONFIG_DEFAULT_DEVICE_TREE="sun8i-a33-ga10h-v1.1"
CONFIG_SPL=y
CONFIG_MACH_SUN8I_A33=y
CONFIG_DRAM_CLK=432
CONFIG_DRAM_ZQ=15291
CONFIG_DRAM_ODT_EN=y
CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
CONFIG_USB0_ID_DET="PH8"
CONFIG_AXP_GPIO=y
CONFIG_VIDEO_LCD_MODE="x:1024,y:600,depth:18,pclk_khz:52000,le:138,ri:162,up:22,lo:10,hs:20,vs:3,sync:3,vmode:0"
CONFIG_VIDEO_LCD_DCLK_PHASE=0
CONFIG_VIDEO_LCD_POWER="PH7"
CONFIG_VIDEO_LCD_BL_EN="PH6"
CONFIG_VIDEO_LCD_BL_PWM="PH0"
CONFIG_VIDEO_LCD_PANEL_LVDS=y
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_REGULATOR_AXP_USB_POWER=y
CONFIG_AXP_DLDO1_VOLT=3300
CONFIG_CONS_INDEX=5
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_OHCI_HCD=y
CONFIG_USB_MUSB_HOST=y
Move setexpr to Kconfig Another shell scripting command that has not been moved. Moved using tools/moveconfig.py using these settings: CMD_SETEXPR bool n y Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> 2015-05-06 00:08:13 +00:00			`CONFIG_ARM=y`
			`CONFIG_ARCH_SUNXI=y`
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com> 2021-06-28 14:17:29 +00:00			`CONFIG_DEFAULT_DEVICE_TREE="sun8i-a33-ga10h-v1.1"`
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com> 2018-04-08 00:27:54 +00:00			`CONFIG_SPL=y`
Move setexpr to Kconfig Another shell scripting command that has not been moved. Moved using tools/moveconfig.py using these settings: CMD_SETEXPR bool n y Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> 2015-05-06 00:08:13 +00:00			`CONFIG_MACH_SUN8I_A33=y`
			`CONFIG_DRAM_CLK=432`
			`CONFIG_DRAM_ZQ=15291`
			`CONFIG_DRAM_ODT_EN=y`
sunxi: Add ga10h v1.1 defconfig The ga10h is an 10" tablet with an A33 or A23 soc, 1G RAM, 8G or 16G nand, sdio wifi, 2 micro usb ports, 1 otg and 1 host and 1 micro sd slot. This commit adds a defconfig for the v1.1 pcb with an a33 soc. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> 2015-05-14 17:01:40 +00:00			`CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"`
sunxi: ga10h: Enable both otg and regular usb host controllers This allows using devices plugged into both ports of the tablet. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> 2015-06-17 19:16:59 +00:00			`CONFIG_USB0_ID_DET="PH8"`
sunxi: Add ga10h v1.1 defconfig The ga10h is an 10" tablet with an A33 or A23 soc, 1G RAM, 8G or 16G nand, sdio wifi, 2 micro usb ports, 1 otg and 1 host and 1 micro sd slot. This commit adds a defconfig for the v1.1 pcb with an a33 soc. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> 2015-05-14 17:01:40 +00:00			`CONFIG_AXP_GPIO=y`
			`CONFIG_VIDEO_LCD_MODE="x:1024,y:600,depth:18,pclk_khz:52000,le:138,ri:162,up:22,lo:10,hs:20,vs:3,sync:3,vmode:0"`
			`CONFIG_VIDEO_LCD_DCLK_PHASE=0`
			`CONFIG_VIDEO_LCD_POWER="PH7"`
			`CONFIG_VIDEO_LCD_BL_EN="PH6"`
			`CONFIG_VIDEO_LCD_BL_PWM="PH0"`
Move setexpr to Kconfig Another shell scripting command that has not been moved. Moved using tools/moveconfig.py using these settings: CMD_SETEXPR bool n y Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> 2015-05-06 00:08:13 +00:00			`CONFIG_VIDEO_LCD_PANEL_LVDS=y`
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com> 2020-07-28 12:46:52 +00:00			`# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set`
sunxi: Switch to PMIC USB power supply VBUS detection Update boards to use the USB power supply driver, as referenced in the device tree, instead of a virtual GPIO. This removes the need for some DM-incompatible special cases in the GPIO driver. The following five boards used AXP0-VBUS-DETECT in their config, but are missing the "usb0_vbus_power-supply" property in their device tree: - Ainol_AW1_defconfig / sun7i-a20-ainol-aw1 - Cubieboard4_defconfig / sun9i-a80-cubieboard4 - Merrii_A80_Optimus_defconfig / sun9i-a80-optimus - Yones_Toptech_BD1078_defconfig / sun7i-a20-yones-toptech-bd1078 - Yones_Toptech_BS1078_V2_defconfig / sun6i-a31s-yones-toptech-bs1078-v2 None of those five boards have the MUSB controller (USB OTG) enabled in their device trees, so this change should not break anything for them. Additionally, the following board intentionally omits the property because VBUS is always enabled: - Nintendo_NES_Classic_Edition_defconfig / sun8i-r16-nintendo-nes-classic The PHY driver already assumes VBUS is enabled when no detection method is available, so again this will not cause any problems. Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com> 2023-01-22 23:46:21 +00:00			`CONFIG_REGULATOR_AXP_USB_POWER=y`
sunxi: power: Make all voltages configurable through Kconfig On boards with axp221/223 pmic-s we already allow configuring most voltages. Make the Kconfig options for these also apply to boards with axp152 / axp209 pmic-s and extend them to configure all voltages. The Kconfig defaults are chosen so that this commit does not introduce any functional changes. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> 2015-09-30 13:22:42 +00:00			`CONFIG_AXP_DLDO1_VOLT=3300`
Convert all of CONFIG_CONS_INDEX to Kconfig This converts the following to Kconfig: CONFIG_CONS_INDEX We have existing entries for this option in a number of places, with different guards on them. They're also sometimes used for things not directly inside of the serial driver. First, introduce a new symbol to guard the use of CONFIG_CONS_INDEX, so that in the case where we don't need this for the serial driver, but for some other use, we can still do it. Next, consolidate all of these into the single entry in drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that we can imply a correct value here to make the defconfig side of this smaller. Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Rework a lot of the logic here, such that I took authorship from Adam, but kept his S-o-B line] Signed-off-by: Tom Rini <trini@konsulko.com> 2018-03-07 00:02:27 +00:00			`CONFIG_CONS_INDEX=5`
sunxi: ga10h: Enable both otg and regular usb host controllers This allows using devices plugged into both ports of the tablet. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> 2015-06-17 19:16:59 +00:00			`CONFIG_USB_EHCI_HCD=y`
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com> 2019-02-07 19:53:03 +00:00			`CONFIG_USB_OHCI_HCD=y`
Tidy up some defconfig files Several files are out of order. This means that when the moveconfig tool moves CONFIG options to Kconfig it generates a large diff. To avoid this, reorder the files first. Signed-off-by: Simon Glass <sjg@chromium.org> 2015-08-19 15:33:42 +00:00			`CONFIG_USB_MUSB_HOST=y`