u-boot/include/configs/j721s2_evm.h

187 lines
6.2 KiB
C
Raw Normal View History

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Configuration header file for K3 J721S2 EVM
*
* Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/
* David Huang <d-huang@ti.com>
*/
#ifndef __CONFIG_J721S2_EVM_H
#define __CONFIG_J721S2_EVM_H
#include <linux/sizes.h>
#include <config_distro_bootcmd.h>
#include <environment/ti/mmc.h>
#include <environment/ti/k3_rproc.h>
#include <environment/ti/ufs.h>
#include <environment/ti/k3_dfu.h>
/* DDR Configuration */
#define CONFIG_SYS_SDRAM_BASE1 0x880000000
/* SPL Loader Configuration */
#if defined(CONFIG_TARGET_J721S2_A72_EVM) || defined(CONFIG_TARGET_J7200_A72_EVM)
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SPL_TEXT_BASE + SZ_4M)
#define CONFIG_SYS_UBOOT_BASE 0x50280000
/* Image load address in RAM for DFU boot*/
#else
#define CONFIG_SYS_UBOOT_BASE 0x50080000
/*
* Maximum size in memory allocated to the SPL BSS. Keep it as tight as
* possible (to allow the build to go through), as this directly affects
* our memory footprint. The less we use for BSS the more we have available
* for everything else.
*/
#define CONFIG_SPL_BSS_MAX_SIZE 0xA000
/*
* Link BSS to be within SPL in a dedicated region located near the top of
* the MCU SRAM, this way making it available also before relocation. Note
* that we are not using the actual top of the MCU SRAM as there is a memory
* location filled in by the boot ROM that we want to read out without any
* interference from the C context.
*/
#define CONFIG_SPL_BSS_START_ADDR (0x41c80000 -\
CONFIG_SPL_BSS_MAX_SIZE)
/* Set the stack right below the SPL BSS section */
#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SPL_BSS_START_ADDR
/* Configure R5 SPL post-relocation malloc pool in DDR */
#define CONFIG_SYS_SPL_MALLOC_START 0x84000000
#define CONFIG_SYS_SPL_MALLOC_SIZE SZ_16M
/* Image load address in RAM for DFU boot*/
#endif
#ifdef CONFIG_SYS_K3_SPL_ATF
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "tispl.bin"
#endif
#define CONFIG_SPL_MAX_SIZE CONFIG_SYS_K3_MAX_DOWNLODABLE_IMAGE_SIZE
#define CONFIG_SYS_BOOTM_LEN SZ_64M
/* U-Boot general configuration */
#define EXTRA_ENV_J721S2_BOARD_SETTINGS \
"default_device_tree=" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \
"findfdt=" \
"setenv name_fdt ${default_device_tree};" \
"setenv fdtfile ${name_fdt}\0" \
"name_kern=Image\0" \
"console=ttyS2,115200n8\0" \
"args_all=setenv optargs earlycon=ns16550a,mmio32,0x02880000 " \
"${mtdparts}\0" \
"run_kern=booti ${loadaddr} ${rd_spec} ${fdtaddr}\0"
#define PARTS_DEFAULT \
/* Linux partitions */ \
"uuid_disk=${uuid_gpt_disk};" \
"name=rootfs,start=0,size=-,uuid=${uuid_gpt_rootfs}\0"
#ifdef CONFIG_SYS_K3_SPL_ATF
#if defined(CONFIG_TARGET_J721S2_R5_EVM)
#define EXTRA_ENV_R5_SPL_RPROC_FW_ARGS_MMC \
"addr_mcur5f0_0load=0x89000000\0" \
"name_mcur5f0_0fw=/lib/firmware/j7-mcu-r5f0_0-fw\0"
#elif defined(CONFIG_TARGET_J7200_R5_EVM)
#define EXTRA_ENV_R5_SPL_RPROC_FW_ARGS_MMC \
"addr_mcur5f0_0load=0x89000000\0" \
"name_mcur5f0_0fw=/lib/firmware/j7200-mcu-r5f0_0-fw\0"
#endif /* CONFIG_TARGET_J721S2_R5_EVM */
#else
#define EXTRA_ENV_R5_SPL_RPROC_FW_ARGS_MMC ""
#endif /* CONFIG_SYS_K3_SPL_ATF */
/* U-Boot MMC-specific configuration */
#define EXTRA_ENV_J721S2_BOARD_SETTINGS_MMC \
"boot=mmc\0" \
"mmcdev=1\0" \
"bootpart=1:2\0" \
"bootdir=/boot\0" \
EXTRA_ENV_R5_SPL_RPROC_FW_ARGS_MMC \
"rd_spec=-\0" \
"init_mmc=run args_all args_mmc\0" \
"get_fdt_mmc=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${name_fdt}\0" \
"get_overlay_mmc=" \
"fdt address ${fdtaddr};" \
"fdt resize 0x100000;" \
"for overlay in $name_overlays;" \
"do;" \
"load mmc ${bootpart} ${dtboaddr} ${bootdir}/${overlay} && " \
"fdt apply ${dtboaddr};" \
"done;\0" \
"partitions=" PARTS_DEFAULT \
"get_kern_mmc=load mmc ${bootpart} ${loadaddr} " \
"${bootdir}/${name_kern}\0" \
"get_fit_mmc=load mmc ${bootpart} ${addr_fit} " \
"${bootdir}/${name_fit}\0" \
"partitions=" PARTS_DEFAULT
/* Set the default list of remote processors to boot */
#if defined(CONFIG_TARGET_J721S2_A72_EVM) || defined(CONFIG_TARGET_J7200_A72_EVM)
#ifdef DEFAULT_RPROCS
#undef DEFAULT_RPROCS
#endif
#endif
#ifdef CONFIG_TARGET_J721S2_A72_EVM
#define DEFAULT_RPROCS "" \
"2 /lib/firmware/j721s2-main-r5f0_0-fw " \
"3 /lib/firmware/j721s2-main-r5f0_1-fw " \
"4 /lib/firmware/j721s2-main-r5f1_0-fw " \
"5 /lib/firmware/j721s2-main-r5f1_1-fw " \
"6 /lib/firmware/j721s2-c71_0-fw " \
"7 /lib/firmware/j721s2-c71_1-fw "
#endif /* CONFIG_TARGET_J721S2_A72_EVM */
#ifdef CONFIG_TARGET_J7200_A72_EVM
#define EXTRA_ENV_CONFIG_MAIN_CPSW0_QSGMII_PHY \
"do_main_cpsw0_qsgmii_phyinit=1\0" \
"init_main_cpsw0_qsgmii_phy=gpio set gpio@22_17;" \
"gpio clear gpio@22_16\0" \
"main_cpsw0_qsgmii_phyinit=" \
"if test ${do_main_cpsw0_qsgmii_phyinit} -eq 1 && test ${dorprocboot} -eq 1 && " \
"test ${boot} = mmc; then " \
"run init_main_cpsw0_qsgmii_phy;" \
"fi;\0"
#define DEFAULT_RPROCS "" \
"2 /lib/firmware/j7200-main-r5f0_0-fw " \
"3 /lib/firmware/j7200-main-r5f0_1-fw "
#endif /* CONFIG_TARGET_J7200_A72_EVM */
#ifndef EXTRA_ENV_CONFIG_MAIN_CPSW0_QSGMII_PHY
#define EXTRA_ENV_CONFIG_MAIN_CPSW0_QSGMII_PHY
#endif
/* set default dfu_bufsiz to 128KB (sector size of OSPI) */
#define EXTRA_ENV_DFUARGS \
DFU_ALT_INFO_MMC \
DFU_ALT_INFO_EMMC \
DFU_ALT_INFO_RAM \
DFU_ALT_INFO_OSPI
#if defined(CONFIG_TARGET_J721S2_A72_EVM) || defined(CONFIG_TARGET_J7200_A72_EVM)
#define EXTRA_ENV_J721S2_BOARD_SETTINGS_MTD \
"mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \
"mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0"
#else
#define EXTRA_ENV_J721S2_BOARD_SETTINGS_MTD
#endif
/* Incorporate settings into the U-Boot environment */
#define CONFIG_EXTRA_ENV_SETTINGS \
DEFAULT_LINUX_BOOT_ENV \
DEFAULT_MMC_TI_ARGS \
DEFAULT_FIT_TI_ARGS \
EXTRA_ENV_J721S2_BOARD_SETTINGS \
EXTRA_ENV_J721S2_BOARD_SETTINGS_MMC \
EXTRA_ENV_RPROC_SETTINGS \
EXTRA_ENV_DFUARGS \
DEFAULT_UFS_TI_ARGS \
EXTRA_ENV_J721S2_BOARD_SETTINGS_MTD \
EXTRA_ENV_CONFIG_MAIN_CPSW0_QSGMII_PHY
/* Now for the remaining common defines */
#include <configs/ti_armv7_common.h>
/* MMC ENV related defines */
#endif /* __CONFIG_J721S2_EVM_H */