u-boot/drivers/net/bcmgenet.c

739 lines
21 KiB
C
Raw Normal View History

// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright (C) 2019 Amit Singh Tomar <amittomer25@gmail.com>
*
* Driver for Broadcom GENETv5 Ethernet controller (as found on the RPi4)
* This driver is based on the Linux driver:
* drivers/net/ethernet/broadcom/genet/bcmgenet.c
* which is: Copyright (c) 2014-2017 Broadcom
*
* The hardware supports multiple queues (16 priority queues and one
* default queue), both for RX and TX. There are 256 DMA descriptors (both
* for TX and RX), and they live in MMIO registers. The hardware allows
* assigning descriptor ranges to queues, but we choose the most simple setup:
* All 256 descriptors are assigned to the default queue (#16).
* Also the Linux driver supports multiple generations of the MAC, whereas
* we only support v5, as used in the Raspberry Pi 4.
*/
#include <log.h>
#include <asm/cache.h>
#include <asm/io.h>
#include <clk.h>
#include <cpu_func.h>
#include <dm.h>
#include <fdt_support.h>
#include <linux/bitops.h>
#include <linux/delay.h>
#include <linux/err.h>
#include <malloc.h>
#include <miiphy.h>
#include <net.h>
#include <dm/of_access.h>
#include <dm/ofnode.h>
#include <linux/iopoll.h>
#include <linux/sizes.h>
#include <asm/dma-mapping.h>
#include <wait_bit.h>
/* Register definitions derived from Linux source */
#define SYS_REV_CTRL 0x00
#define SYS_PORT_CTRL 0x04
#define PORT_MODE_EXT_GPHY 3
#define GENET_SYS_OFF 0x0000
#define SYS_RBUF_FLUSH_CTRL (GENET_SYS_OFF + 0x08)
#define SYS_TBUF_FLUSH_CTRL (GENET_SYS_OFF + 0x0c)
#define GENET_EXT_OFF 0x0080
#define EXT_RGMII_OOB_CTRL (GENET_EXT_OFF + 0x0c)
#define RGMII_LINK BIT(4)
#define OOB_DISABLE BIT(5)
#define RGMII_MODE_EN BIT(6)
#define ID_MODE_DIS BIT(16)
#define GENET_RBUF_OFF 0x0300
#define RBUF_TBUF_SIZE_CTRL (GENET_RBUF_OFF + 0xb4)
#define RBUF_CTRL (GENET_RBUF_OFF + 0x00)
#define RBUF_ALIGN_2B BIT(1)
#define GENET_UMAC_OFF 0x0800
#define UMAC_MIB_CTRL (GENET_UMAC_OFF + 0x580)
#define UMAC_MAX_FRAME_LEN (GENET_UMAC_OFF + 0x014)
#define UMAC_MAC0 (GENET_UMAC_OFF + 0x00c)
#define UMAC_MAC1 (GENET_UMAC_OFF + 0x010)
#define UMAC_CMD (GENET_UMAC_OFF + 0x008)
#define MDIO_CMD (GENET_UMAC_OFF + 0x614)
#define UMAC_TX_FLUSH (GENET_UMAC_OFF + 0x334)
#define MDIO_START_BUSY BIT(29)
#define MDIO_READ_FAIL BIT(28)
#define MDIO_RD (2 << 26)
#define MDIO_WR BIT(26)
#define MDIO_PMD_SHIFT 21
#define MDIO_PMD_MASK 0x1f
#define MDIO_REG_SHIFT 16
#define MDIO_REG_MASK 0x1f
#define CMD_TX_EN BIT(0)
#define CMD_RX_EN BIT(1)
#define UMAC_SPEED_10 0
#define UMAC_SPEED_100 1
#define UMAC_SPEED_1000 2
#define UMAC_SPEED_2500 3
#define CMD_SPEED_SHIFT 2
#define CMD_SPEED_MASK 3
#define CMD_SW_RESET BIT(13)
#define CMD_LCL_LOOP_EN BIT(15)
#define CMD_TX_EN BIT(0)
#define CMD_RX_EN BIT(1)
#define MIB_RESET_RX BIT(0)
#define MIB_RESET_RUNT BIT(1)
#define MIB_RESET_TX BIT(2)
/* total number of Buffer Descriptors, same for Rx/Tx */
#define TOTAL_DESCS 256
#define RX_DESCS TOTAL_DESCS
#define TX_DESCS TOTAL_DESCS
#define DEFAULT_Q 0x10
/* Body(1500) + EH_SIZE(14) + VLANTAG(4) + BRCMTAG(6) + FCS(4) = 1528.
* 1536 is multiple of 256 bytes
*/
#define ENET_BRCM_TAG_LEN 6
#define ENET_PAD 8
#define ENET_MAX_MTU_SIZE (ETH_DATA_LEN + ETH_HLEN + \
VLAN_HLEN + ENET_BRCM_TAG_LEN + \
ETH_FCS_LEN + ENET_PAD)
/* Tx/Rx Dma Descriptor common bits */
#define DMA_EN BIT(0)
#define DMA_RING_BUF_EN_SHIFT 0x01
#define DMA_RING_BUF_EN_MASK 0xffff
#define DMA_BUFLENGTH_MASK 0x0fff
#define DMA_BUFLENGTH_SHIFT 16
#define DMA_RING_SIZE_SHIFT 16
#define DMA_OWN 0x8000
#define DMA_EOP 0x4000
#define DMA_SOP 0x2000
#define DMA_WRAP 0x1000
#define DMA_MAX_BURST_LENGTH 0x8
/* Tx specific DMA descriptor bits */
#define DMA_TX_UNDERRUN 0x0200
#define DMA_TX_APPEND_CRC 0x0040
#define DMA_TX_OW_CRC 0x0020
#define DMA_TX_DO_CSUM 0x0010
#define DMA_TX_QTAG_SHIFT 7
/* DMA rings size */
#define DMA_RING_SIZE 0x40
#define DMA_RINGS_SIZE (DMA_RING_SIZE * (DEFAULT_Q + 1))
/* DMA descriptor */
#define DMA_DESC_LENGTH_STATUS 0x00
#define DMA_DESC_ADDRESS_LO 0x04
#define DMA_DESC_ADDRESS_HI 0x08
#define DMA_DESC_SIZE 12
#define GENET_RX_OFF 0x2000
#define GENET_RDMA_REG_OFF \
(GENET_RX_OFF + TOTAL_DESCS * DMA_DESC_SIZE)
#define GENET_TX_OFF 0x4000
#define GENET_TDMA_REG_OFF \
(GENET_TX_OFF + TOTAL_DESCS * DMA_DESC_SIZE)
#define DMA_FC_THRESH_HI (RX_DESCS >> 4)
#define DMA_FC_THRESH_LO 5
#define DMA_FC_THRESH_VALUE ((DMA_FC_THRESH_LO << 16) | \
DMA_FC_THRESH_HI)
#define DMA_XOFF_THRESHOLD_SHIFT 16
#define TDMA_RING_REG_BASE \
(GENET_TDMA_REG_OFF + DEFAULT_Q * DMA_RING_SIZE)
#define TDMA_READ_PTR (TDMA_RING_REG_BASE + 0x00)
#define TDMA_CONS_INDEX (TDMA_RING_REG_BASE + 0x08)
#define TDMA_PROD_INDEX (TDMA_RING_REG_BASE + 0x0c)
#define DMA_RING_BUF_SIZE 0x10
#define DMA_START_ADDR 0x14
#define DMA_END_ADDR 0x1c
#define DMA_MBUF_DONE_THRESH 0x24
#define TDMA_FLOW_PERIOD (TDMA_RING_REG_BASE + 0x28)
#define TDMA_WRITE_PTR (TDMA_RING_REG_BASE + 0x2c)
#define RDMA_RING_REG_BASE \
(GENET_RDMA_REG_OFF + DEFAULT_Q * DMA_RING_SIZE)
#define RDMA_WRITE_PTR (RDMA_RING_REG_BASE + 0x00)
#define RDMA_PROD_INDEX (RDMA_RING_REG_BASE + 0x08)
#define RDMA_CONS_INDEX (RDMA_RING_REG_BASE + 0x0c)
#define RDMA_XON_XOFF_THRESH (RDMA_RING_REG_BASE + 0x28)
#define RDMA_READ_PTR (RDMA_RING_REG_BASE + 0x2c)
#define TDMA_REG_BASE (GENET_TDMA_REG_OFF + DMA_RINGS_SIZE)
#define RDMA_REG_BASE (GENET_RDMA_REG_OFF + DMA_RINGS_SIZE)
#define DMA_RING_CFG 0x00
#define DMA_CTRL 0x04
#define DMA_SCB_BURST_SIZE 0x0c
#define RX_BUF_LENGTH 2048
#define RX_TOTAL_BUFSIZE (RX_BUF_LENGTH * RX_DESCS)
#define RX_BUF_OFFSET 2
struct bcmgenet_eth_priv {
char rxbuffer[RX_TOTAL_BUFSIZE] __aligned(ARCH_DMA_MINALIGN);
void *mac_reg;
void *tx_desc_base;
void *rx_desc_base;
int tx_index;
int rx_index;
int c_index;
int phyaddr;
u32 interface;
u32 speed;
struct phy_device *phydev;
struct mii_dev *bus;
};
static void bcmgenet_umac_reset(struct bcmgenet_eth_priv *priv)
{
u32 reg;
reg = readl(priv->mac_reg + SYS_RBUF_FLUSH_CTRL);
reg |= BIT(1);
writel(reg, (priv->mac_reg + SYS_RBUF_FLUSH_CTRL));
udelay(10);
reg &= ~BIT(1);
writel(reg, (priv->mac_reg + SYS_RBUF_FLUSH_CTRL));
udelay(10);
writel(0, (priv->mac_reg + SYS_RBUF_FLUSH_CTRL));
udelay(10);
writel(0, priv->mac_reg + UMAC_CMD);
writel(CMD_SW_RESET | CMD_LCL_LOOP_EN, priv->mac_reg + UMAC_CMD);
udelay(2);
writel(0, priv->mac_reg + UMAC_CMD);
/* clear tx/rx counter */
writel(MIB_RESET_RX | MIB_RESET_TX | MIB_RESET_RUNT,
priv->mac_reg + UMAC_MIB_CTRL);
writel(0, priv->mac_reg + UMAC_MIB_CTRL);
writel(ENET_MAX_MTU_SIZE, priv->mac_reg + UMAC_MAX_FRAME_LEN);
/* init rx registers, enable ip header optimization */
reg = readl(priv->mac_reg + RBUF_CTRL);
reg |= RBUF_ALIGN_2B;
writel(reg, (priv->mac_reg + RBUF_CTRL));
writel(1, (priv->mac_reg + RBUF_TBUF_SIZE_CTRL));
}
static int bcmgenet_gmac_write_hwaddr(struct udevice *dev)
{
struct bcmgenet_eth_priv *priv = dev_get_priv(dev);
struct eth_pdata *pdata = dev_get_platdata(dev);
uchar *addr = pdata->enetaddr;
u32 reg;
reg = addr[0] << 24 | addr[1] << 16 | addr[2] << 8 | addr[3];
writel_relaxed(reg, priv->mac_reg + UMAC_MAC0);
reg = addr[4] << 8 | addr[5];
writel_relaxed(reg, priv->mac_reg + UMAC_MAC1);
return 0;
}
static void bcmgenet_disable_dma(struct bcmgenet_eth_priv *priv)
{
clrbits_32(priv->mac_reg + TDMA_REG_BASE + DMA_CTRL, DMA_EN);
clrbits_32(priv->mac_reg + RDMA_REG_BASE + DMA_CTRL, DMA_EN);
writel(1, priv->mac_reg + UMAC_TX_FLUSH);
udelay(10);
writel(0, priv->mac_reg + UMAC_TX_FLUSH);
}
static void bcmgenet_enable_dma(struct bcmgenet_eth_priv *priv)
{
u32 dma_ctrl = (1 << (DEFAULT_Q + DMA_RING_BUF_EN_SHIFT)) | DMA_EN;
writel(dma_ctrl, priv->mac_reg + TDMA_REG_BASE + DMA_CTRL);
setbits_32(priv->mac_reg + RDMA_REG_BASE + DMA_CTRL, dma_ctrl);
}
static int bcmgenet_gmac_eth_send(struct udevice *dev, void *packet, int length)
{
struct bcmgenet_eth_priv *priv = dev_get_priv(dev);
void *desc_base = priv->tx_desc_base + priv->tx_index * DMA_DESC_SIZE;
u32 len_stat = length << DMA_BUFLENGTH_SHIFT;
ulong packet_aligned = rounddown((ulong)packet, ARCH_DMA_MINALIGN);
u32 prod_index, cons;
u32 tries = 100;
prod_index = readl(priv->mac_reg + TDMA_PROD_INDEX);
/* There is actually no reason for the rounding here, but the ARMv7
* implementation of flush_dcache_range() checks for aligned
* boundaries of the flushed range.
* Adjust them here to pass that check and avoid misleading messages.
*/
flush_dcache_range(packet_aligned,
packet_aligned + roundup(length, ARCH_DMA_MINALIGN));
len_stat |= 0x3F << DMA_TX_QTAG_SHIFT;
len_stat |= DMA_TX_APPEND_CRC | DMA_SOP | DMA_EOP;
/* Set-up packet for transmission */
writel(lower_32_bits((ulong)packet), (desc_base + DMA_DESC_ADDRESS_LO));
writel(upper_32_bits((ulong)packet), (desc_base + DMA_DESC_ADDRESS_HI));
writel(len_stat, (desc_base + DMA_DESC_LENGTH_STATUS));
/* Increment index and start transmission */
if (++priv->tx_index >= TX_DESCS)
priv->tx_index = 0;
prod_index++;
/* Start Transmisson */
writel(prod_index, priv->mac_reg + TDMA_PROD_INDEX);
do {
cons = readl(priv->mac_reg + TDMA_CONS_INDEX);
} while ((cons & 0xffff) < prod_index && --tries);
if (!tries)
return -ETIMEDOUT;
return 0;
}
/* Check whether all cache lines affected by an invalidate are within
* the buffer, to make sure we don't accidentally lose unrelated dirty
* data stored nearby.
* Alignment of the buffer start address will be checked in the implementation
* of invalidate_dcache_range().
*/
static void invalidate_dcache_check(unsigned long addr, size_t size,
size_t buffer_size)
{
size_t inval_size = roundup(size, ARCH_DMA_MINALIGN);
if (unlikely(inval_size > buffer_size))
printf("WARNING: Cache invalidate area exceeds buffer size\n");
invalidate_dcache_range(addr, addr + inval_size);
}
static int bcmgenet_gmac_eth_recv(struct udevice *dev,
int flags, uchar **packetp)
{
struct bcmgenet_eth_priv *priv = dev_get_priv(dev);
void *desc_base = priv->rx_desc_base + priv->rx_index * DMA_DESC_SIZE;
u32 prod_index = readl(priv->mac_reg + RDMA_PROD_INDEX);
u32 length, addr;
if (prod_index == priv->c_index)
return -EAGAIN;
length = readl(desc_base + DMA_DESC_LENGTH_STATUS);
length = (length >> DMA_BUFLENGTH_SHIFT) & DMA_BUFLENGTH_MASK;
addr = readl(desc_base + DMA_DESC_ADDRESS_LO);
invalidate_dcache_check(addr, length, RX_BUF_LENGTH);
/* To cater for the IP header alignment the hardware does.
* This would actually not be needed if we don't program
* RBUF_ALIGN_2B
*/
*packetp = (uchar *)(ulong)addr + RX_BUF_OFFSET;
return length - RX_BUF_OFFSET;
}
static int bcmgenet_gmac_free_pkt(struct udevice *dev, uchar *packet,
int length)
{
struct bcmgenet_eth_priv *priv = dev_get_priv(dev);
/* Tell the MAC we have consumed that last receive buffer. */
priv->c_index = (priv->c_index + 1) & 0xFFFF;
writel(priv->c_index, priv->mac_reg + RDMA_CONS_INDEX);
/* Forward our descriptor pointer, wrapping around if needed. */
if (++priv->rx_index >= RX_DESCS)
priv->rx_index = 0;
return 0;
}
static void rx_descs_init(struct bcmgenet_eth_priv *priv)
{
char *rxbuffs = &priv->rxbuffer[0];
u32 len_stat, i;
void *desc_base = priv->rx_desc_base;
len_stat = (RX_BUF_LENGTH << DMA_BUFLENGTH_SHIFT) | DMA_OWN;
for (i = 0; i < RX_DESCS; i++) {
writel(lower_32_bits((uintptr_t)&rxbuffs[i * RX_BUF_LENGTH]),
desc_base + i * DMA_DESC_SIZE + DMA_DESC_ADDRESS_LO);
writel(upper_32_bits((uintptr_t)&rxbuffs[i * RX_BUF_LENGTH]),
desc_base + i * DMA_DESC_SIZE + DMA_DESC_ADDRESS_HI);
writel(len_stat,
desc_base + i * DMA_DESC_SIZE + DMA_DESC_LENGTH_STATUS);
}
}
static void rx_ring_init(struct bcmgenet_eth_priv *priv)
{
writel(DMA_MAX_BURST_LENGTH,
priv->mac_reg + RDMA_REG_BASE + DMA_SCB_BURST_SIZE);
writel(0x0, priv->mac_reg + RDMA_RING_REG_BASE + DMA_START_ADDR);
writel(0x0, priv->mac_reg + RDMA_READ_PTR);
writel(0x0, priv->mac_reg + RDMA_WRITE_PTR);
writel(RX_DESCS * DMA_DESC_SIZE / 4 - 1,
priv->mac_reg + RDMA_RING_REG_BASE + DMA_END_ADDR);
bcmgenet: fix DMA buffer management This commit fixes a serious issue occurring when several network commands are run on a raspberry pi 4 board: for instance a "dhcp" command and then one or several "tftp" commands. In this case, packet recv callbacks were called several times on the same packets, and send function was failing most of the time. note: if the boot procedure is made of a single network command, the issue is not visible. The issue is related to management of the packet ring buffers (producer / consumer) and DMA. Each time a packet is received, the ethernet device stores it in the buffer and increments an index called RDMA_PROD_INDEX. Each time the driver outputs a received packet, it increments another index called RDMA_CONS_INDEX. Between each pair of network commands, as part of the driver 'start' function, previous code tried to reset both RDMA_CONS_INDEX and RDMA_PROD_INDEX to 0. But RDMA_PROD_INDEX cannot be written from driver side, thus its value was actually not updated, and only RDMA_CONS_INDEX was reset to 0. This was resulting in a major synchronization issue between the driver and the device. Most visible behavior was that the driver seemed to receive again the packets from the previous commands (e.g. DHCP response packets "received" again when performing the first TFTP command). This fix consists in setting RDMA_CONS_INDEX to the same value as RDMA_PROD_INDEX, when resetting the driver. The same kind of fix was needed on the TX side, and a few variables had to be reset accordingly (c_index, tx_index, rx_index). The rx_index and tx_index have only 256 entries so the bottom 8 bits must be masked off. Originated-by: Etienne Dublé <etienne.duble@imag.fr> Signed-off-by: Jason Wessel <jason.wessel@windriver.com> Tested-by: Petr Tesarik <ptesarik@suse.com> Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2020-07-17 13:31:59 +00:00
/* cannot init RDMA_PROD_INDEX to 0, so align RDMA_CONS_INDEX on it instead */
priv->c_index = readl(priv->mac_reg + RDMA_PROD_INDEX);
writel(priv->c_index, priv->mac_reg + RDMA_CONS_INDEX);
priv->rx_index = priv->c_index;
priv->rx_index &= 0xFF;
writel((RX_DESCS << DMA_RING_SIZE_SHIFT) | RX_BUF_LENGTH,
priv->mac_reg + RDMA_RING_REG_BASE + DMA_RING_BUF_SIZE);
writel(DMA_FC_THRESH_VALUE, priv->mac_reg + RDMA_XON_XOFF_THRESH);
writel(1 << DEFAULT_Q, priv->mac_reg + RDMA_REG_BASE + DMA_RING_CFG);
}
static void tx_ring_init(struct bcmgenet_eth_priv *priv)
{
writel(DMA_MAX_BURST_LENGTH,
priv->mac_reg + TDMA_REG_BASE + DMA_SCB_BURST_SIZE);
writel(0x0, priv->mac_reg + TDMA_RING_REG_BASE + DMA_START_ADDR);
writel(0x0, priv->mac_reg + TDMA_READ_PTR);
writel(0x0, priv->mac_reg + TDMA_WRITE_PTR);
writel(TX_DESCS * DMA_DESC_SIZE / 4 - 1,
priv->mac_reg + TDMA_RING_REG_BASE + DMA_END_ADDR);
bcmgenet: fix DMA buffer management This commit fixes a serious issue occurring when several network commands are run on a raspberry pi 4 board: for instance a "dhcp" command and then one or several "tftp" commands. In this case, packet recv callbacks were called several times on the same packets, and send function was failing most of the time. note: if the boot procedure is made of a single network command, the issue is not visible. The issue is related to management of the packet ring buffers (producer / consumer) and DMA. Each time a packet is received, the ethernet device stores it in the buffer and increments an index called RDMA_PROD_INDEX. Each time the driver outputs a received packet, it increments another index called RDMA_CONS_INDEX. Between each pair of network commands, as part of the driver 'start' function, previous code tried to reset both RDMA_CONS_INDEX and RDMA_PROD_INDEX to 0. But RDMA_PROD_INDEX cannot be written from driver side, thus its value was actually not updated, and only RDMA_CONS_INDEX was reset to 0. This was resulting in a major synchronization issue between the driver and the device. Most visible behavior was that the driver seemed to receive again the packets from the previous commands (e.g. DHCP response packets "received" again when performing the first TFTP command). This fix consists in setting RDMA_CONS_INDEX to the same value as RDMA_PROD_INDEX, when resetting the driver. The same kind of fix was needed on the TX side, and a few variables had to be reset accordingly (c_index, tx_index, rx_index). The rx_index and tx_index have only 256 entries so the bottom 8 bits must be masked off. Originated-by: Etienne Dublé <etienne.duble@imag.fr> Signed-off-by: Jason Wessel <jason.wessel@windriver.com> Tested-by: Petr Tesarik <ptesarik@suse.com> Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2020-07-17 13:31:59 +00:00
/* cannot init TDMA_CONS_INDEX to 0, so align TDMA_PROD_INDEX on it instead */
priv->tx_index = readl(priv->mac_reg + TDMA_CONS_INDEX);
writel(priv->tx_index, priv->mac_reg + TDMA_PROD_INDEX);
priv->tx_index &= 0xFF;
writel(0x1, priv->mac_reg + TDMA_RING_REG_BASE + DMA_MBUF_DONE_THRESH);
writel(0x0, priv->mac_reg + TDMA_FLOW_PERIOD);
writel((TX_DESCS << DMA_RING_SIZE_SHIFT) | RX_BUF_LENGTH,
priv->mac_reg + TDMA_RING_REG_BASE + DMA_RING_BUF_SIZE);
writel(1 << DEFAULT_Q, priv->mac_reg + TDMA_REG_BASE + DMA_RING_CFG);
}
static int bcmgenet_adjust_link(struct bcmgenet_eth_priv *priv)
{
struct phy_device *phy_dev = priv->phydev;
u32 speed;
switch (phy_dev->speed) {
case SPEED_1000:
speed = UMAC_SPEED_1000;
break;
case SPEED_100:
speed = UMAC_SPEED_100;
break;
case SPEED_10:
speed = UMAC_SPEED_10;
break;
default:
printf("bcmgenet: Unsupported PHY speed: %d\n", phy_dev->speed);
return -EINVAL;
}
clrsetbits_32(priv->mac_reg + EXT_RGMII_OOB_CTRL, OOB_DISABLE,
RGMII_LINK | RGMII_MODE_EN);
if (phy_dev->interface == PHY_INTERFACE_MODE_RGMII ||
phy_dev->interface == PHY_INTERFACE_MODE_RGMII_RXID)
setbits_32(priv->mac_reg + EXT_RGMII_OOB_CTRL, ID_MODE_DIS);
writel(speed << CMD_SPEED_SHIFT, (priv->mac_reg + UMAC_CMD));
return 0;
}
static int bcmgenet_gmac_eth_start(struct udevice *dev)
{
struct bcmgenet_eth_priv *priv = dev_get_priv(dev);
int ret;
priv->tx_desc_base = priv->mac_reg + GENET_TX_OFF;
priv->rx_desc_base = priv->mac_reg + GENET_RX_OFF;
bcmgenet_umac_reset(priv);
bcmgenet_gmac_write_hwaddr(dev);
/* Disable RX/TX DMA and flush TX queues */
bcmgenet_disable_dma(priv);
rx_ring_init(priv);
rx_descs_init(priv);
tx_ring_init(priv);
/* Enable RX/TX DMA */
bcmgenet_enable_dma(priv);
/* read PHY properties over the wire from generic PHY set-up */
ret = phy_startup(priv->phydev);
if (ret) {
printf("bcmgenet: PHY startup failed: %d\n", ret);
return ret;
}
/* Update MAC registers based on PHY property */
ret = bcmgenet_adjust_link(priv);
if (ret) {
printf("bcmgenet: adjust PHY link failed: %d\n", ret);
return ret;
}
/* Enable Rx/Tx */
setbits_32(priv->mac_reg + UMAC_CMD, CMD_TX_EN | CMD_RX_EN);
return 0;
}
static int bcmgenet_phy_init(struct bcmgenet_eth_priv *priv, void *dev)
{
struct phy_device *phydev;
int ret;
phydev = phy_connect(priv->bus, priv->phyaddr, dev, priv->interface);
if (!phydev)
return -ENODEV;
phydev->supported &= PHY_GBIT_FEATURES;
if (priv->speed) {
ret = phy_set_supported(priv->phydev, priv->speed);
if (ret)
return ret;
}
phydev->advertising = phydev->supported;
phy_connect_dev(phydev, dev);
priv->phydev = phydev;
phy_config(priv->phydev);
return 0;
}
static void bcmgenet_mdio_start(struct bcmgenet_eth_priv *priv)
{
setbits_32(priv->mac_reg + MDIO_CMD, MDIO_START_BUSY);
}
static int bcmgenet_mdio_write(struct mii_dev *bus, int addr, int devad,
int reg, u16 value)
{
struct udevice *dev = bus->priv;
struct bcmgenet_eth_priv *priv = dev_get_priv(dev);
u32 val;
/* Prepare the read operation */
val = MDIO_WR | (addr << MDIO_PMD_SHIFT) |
(reg << MDIO_REG_SHIFT) | (0xffff & value);
writel_relaxed(val, priv->mac_reg + MDIO_CMD);
/* Start MDIO transaction */
bcmgenet_mdio_start(priv);
return wait_for_bit_32(priv->mac_reg + MDIO_CMD,
MDIO_START_BUSY, false, 20, true);
}
static int bcmgenet_mdio_read(struct mii_dev *bus, int addr, int devad, int reg)
{
struct udevice *dev = bus->priv;
struct bcmgenet_eth_priv *priv = dev_get_priv(dev);
u32 val;
int ret;
/* Prepare the read operation */
val = MDIO_RD | (addr << MDIO_PMD_SHIFT) | (reg << MDIO_REG_SHIFT);
writel_relaxed(val, priv->mac_reg + MDIO_CMD);
/* Start MDIO transaction */
bcmgenet_mdio_start(priv);
ret = wait_for_bit_32(priv->mac_reg + MDIO_CMD,
MDIO_START_BUSY, false, 20, true);
if (ret)
return ret;
val = readl_relaxed(priv->mac_reg + MDIO_CMD);
return val & 0xffff;
}
static int bcmgenet_mdio_init(const char *name, struct udevice *priv)
{
struct mii_dev *bus = mdio_alloc();
if (!bus) {
debug("Failed to allocate MDIO bus\n");
return -ENOMEM;
}
bus->read = bcmgenet_mdio_read;
bus->write = bcmgenet_mdio_write;
snprintf(bus->name, sizeof(bus->name), name);
bus->priv = (void *)priv;
return mdio_register(bus);
}
/* We only support RGMII (as used on the RPi4). */
static int bcmgenet_interface_set(struct bcmgenet_eth_priv *priv)
{
phy_interface_t phy_mode = priv->interface;
switch (phy_mode) {
case PHY_INTERFACE_MODE_RGMII:
case PHY_INTERFACE_MODE_RGMII_RXID:
writel(PORT_MODE_EXT_GPHY, priv->mac_reg + SYS_PORT_CTRL);
break;
default:
printf("unknown phy mode: %d\n", priv->interface);
return -EINVAL;
}
return 0;
}
static int bcmgenet_eth_probe(struct udevice *dev)
{
struct eth_pdata *pdata = dev_get_platdata(dev);
struct bcmgenet_eth_priv *priv = dev_get_priv(dev);
ofnode mdio_node;
const char *name;
u32 reg;
int ret;
u8 major;
priv->mac_reg = map_physmem(pdata->iobase, SZ_64K, MAP_NOCACHE);
priv->interface = pdata->phy_interface;
priv->speed = pdata->max_speed;
/* Read GENET HW version */
reg = readl_relaxed(priv->mac_reg + SYS_REV_CTRL);
major = (reg >> 24) & 0x0f;
if (major != 6) {
if (major == 5)
major = 4;
else if (major == 0)
major = 1;
printf("Unsupported GENETv%d.%d\n", major, (reg >> 16) & 0x0f);
return -ENODEV;
}
ret = bcmgenet_interface_set(priv);
if (ret)
return ret;
writel(0, priv->mac_reg + SYS_RBUF_FLUSH_CTRL);
udelay(10);
/* disable MAC while updating its registers */
writel(0, priv->mac_reg + UMAC_CMD);
/* issue soft reset with (rg)mii loopback to ensure a stable rxclk */
writel(CMD_SW_RESET | CMD_LCL_LOOP_EN, priv->mac_reg + UMAC_CMD);
mdio_node = dev_read_first_subnode(dev);
name = ofnode_get_name(mdio_node);
ret = bcmgenet_mdio_init(name, dev);
if (ret)
return ret;
priv->bus = miiphy_get_dev_by_name(name);
return bcmgenet_phy_init(priv, dev);
}
static void bcmgenet_gmac_eth_stop(struct udevice *dev)
{
struct bcmgenet_eth_priv *priv = dev_get_priv(dev);
clrbits_32(priv->mac_reg + UMAC_CMD, CMD_TX_EN | CMD_RX_EN);
bcmgenet_disable_dma(priv);
}
static const struct eth_ops bcmgenet_gmac_eth_ops = {
.start = bcmgenet_gmac_eth_start,
.write_hwaddr = bcmgenet_gmac_write_hwaddr,
.send = bcmgenet_gmac_eth_send,
.recv = bcmgenet_gmac_eth_recv,
.free_pkt = bcmgenet_gmac_free_pkt,
.stop = bcmgenet_gmac_eth_stop,
};
static int bcmgenet_eth_ofdata_to_platdata(struct udevice *dev)
{
struct eth_pdata *pdata = dev_get_platdata(dev);
struct bcmgenet_eth_priv *priv = dev_get_priv(dev);
struct ofnode_phandle_args phy_node;
const char *phy_mode;
int ret;
pdata->iobase = dev_read_addr(dev);
/* Get phy mode from DT */
pdata->phy_interface = -1;
phy_mode = dev_read_string(dev, "phy-mode");
if (phy_mode)
pdata->phy_interface = phy_get_interface_by_name(phy_mode);
if (pdata->phy_interface == -1) {
debug("%s: Invalid PHY interface '%s'\n", __func__, phy_mode);
return -EINVAL;
}
ret = dev_read_phandle_with_args(dev, "phy-handle", NULL, 0, 0,
&phy_node);
if (!ret) {
ofnode_read_s32(phy_node.node, "reg", &priv->phyaddr);
ofnode_read_s32(phy_node.node, "max-speed", &pdata->max_speed);
}
return 0;
}
/* The BCM2711 implementation has a limited burst length compared to a generic
* GENETv5 version, but we go with that shorter value (8) in both cases, for
* the sake of simplicity.
*/
static const struct udevice_id bcmgenet_eth_ids[] = {
{.compatible = "brcm,genet-v5"},
{.compatible = "brcm,bcm2711-genet-v5"},
{}
};
U_BOOT_DRIVER(eth_bcmgenet) = {
.name = "eth_bcmgenet",
.id = UCLASS_ETH,
.of_match = bcmgenet_eth_ids,
.ofdata_to_platdata = bcmgenet_eth_ofdata_to_platdata,
.probe = bcmgenet_eth_probe,
.ops = &bcmgenet_gmac_eth_ops,
.priv_auto_alloc_size = sizeof(struct bcmgenet_eth_priv),
.platdata_auto_alloc_size = sizeof(struct eth_pdata),
.flags = DM_FLAG_ALLOC_PRIV_DMA,
};