u-boot/arch/arm/dts/imx6qdl-dhcom-drc02.dtsi

// SPDX-License-Identifier: GPL-2.0+
/*
 * Copyright (C) 2021 DH electronics GmbH
 */

/ {
	chosen {
		stdout-path = "serial0:115200n8";
	};
};

/*
 * Special SoM hardware required which uses the pins from micro SD card. The
 * pins SD3_DAT0 and SD3_DAT1 are muxed as can2 Tx and Rx. The signals for can2
 * Tx and Rx are routed to the DHCOM UART1 rts/cts pins. Therefore the micro SD
 * card must be disabled and the uart1 rts/cts must be output on other DHCOM
 * pins, see uart1 and usdhc3 node below.
 */
&can2 {
	status = "okay";
};

&gpio1 {
	/*
	 * NOTE: On DRC02, the RS485_RX_En is controlled by a separate
	 * GPIO line, however the i.MX6 UART driver assumes RX happens
	 * during TX anyway and that it only controls drive enable DE
	 * line. Hence, the RX is always enabled here.
	 */
	rs485-rx-en-hog {
		gpio-hog;
		gpios = <18 0>; /* GPIO Q */
		line-name = "rs485-rx-en";
		output-low;
	};
};

&gpio3 {
	gpio-line-names =
		"", "", "", "", "", "", "", "",
		"", "", "", "", "", "", "", "",
		"", "", "", "", "", "", "", "",
		"", "", "", "DRC02-In1", "", "", "", "";
};

&gpio4 {
	gpio-line-names =
		"", "", "", "", "", "DHCOM-E", "DRC02-In2", "DHCOM-H",
		"DHCOM-I", "DRC02-HW0", "", "", "", "", "", "",
		"", "", "", "", "DRC02-Out1", "", "", "",
		"", "", "", "", "", "", "", "";
};

&gpio6 {
	gpio-line-names =
		"", "", "", "DRC02-Out2", "", "", "SOM-HW1", "",
		"", "", "", "", "", "", "DRC02-HW2", "DRC02-HW1",
		"", "", "", "", "", "", "", "",
		"", "", "", "", "", "", "", "";
};

&i2c1 {
	eeprom@50 {
		compatible = "atmel,24c04";
		reg = <0x50>;
		pagesize = <16>;
	};
};

&uart1 {
	/*
	 * Due to the use of can2 the signals for can2 Tx and Rx are routed to
	 * DHCOM UART1 rts/cts pins. Therefore this UART have to use DHCOM GPIOs
	 * for rts/cts. So configure DHCOM GPIO I as rts and GPIO M as cts.
	 */
	/delete-property/ uart-has-rtscts;
	cts-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>; /* GPIO M */
	pinctrl-0 = <&pinctrl_uart1 &pinctrl_dhcom_i &pinctrl_dhcom_m>;
	pinctrl-names = "default";
	rts-gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>; /* GPIO I */
};

&uart5 {
	/*
	 * On DRC02 this UART is used as RS485 interface and RS485_TX_En is
	 * controlled by DHCOM GPIO P. So remove rts/cts pins and the property
	 * uart-has-rtscts from this UART and add the DHCOM GPIO P pin via
	 * rts-gpios. The RS485_RX_En is controlled by DHCOM GPIO Q, see gpio1
	 * node above.
	 */
	/delete-property/ uart-has-rtscts;
	linux,rs485-enabled-at-boot-time;
	pinctrl-0 = <&pinctrl_uart5_core &pinctrl_dhcom_p &pinctrl_dhcom_q>;
	pinctrl-names = "default";
	rts-gpios = <&gpio7 13 GPIO_ACTIVE_HIGH>; /* GPIO P */
};

&usbh1 {
	disable-over-current;
};

&usdhc2 { /* SD card */
	status = "okay";
};

&usdhc3 {
	/*
	 * Due to the use of can2 the micro SD card on module have to be
	 * disabled, because the pins SD3_DAT0 and SD3_DAT1 are muxed as
	 * can2 Tx and Rx.
	 */
	status = "disabled";
};

&iomuxc {
	pinctrl-0 = <
			/*
			 * The following DHCOM GPIOs are used on this board.
			 * Therefore, they have been removed from the list below.
			 * I: uart1 rts
			 * M: uart1 cts
			 * P: uart5 rs485-tx-en
			 * Q: uart5 rs485-rx-en
			 */
			&pinctrl_hog_base
			&pinctrl_dhcom_a &pinctrl_dhcom_b &pinctrl_dhcom_c
			&pinctrl_dhcom_d &pinctrl_dhcom_e &pinctrl_dhcom_f
			&pinctrl_dhcom_g &pinctrl_dhcom_h
			&pinctrl_dhcom_j &pinctrl_dhcom_k &pinctrl_dhcom_l
			&pinctrl_dhcom_n &pinctrl_dhcom_o
			&pinctrl_dhcom_r
			&pinctrl_dhcom_s &pinctrl_dhcom_t &pinctrl_dhcom_u
			&pinctrl_dhcom_v &pinctrl_dhcom_w &pinctrl_dhcom_int
		>;
	pinctrl-names = "default";

	pinctrl_uart5_core: uart5-core-grp {
		fsl,pins = <
			MX6QDL_PAD_CSI0_DAT14__UART5_TX_DATA	0x1b0b1
			MX6QDL_PAD_CSI0_DAT15__UART5_RX_DATA	0x1b0b1
		>;
	};
};