u-boot/configs/iNet_D978_rev2_defconfig

CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
CONFIG_DEFAULT_DEVICE_TREE="sun8i-a33-inet-d978-rev2"
CONFIG_SPL=y
CONFIG_MACH_SUN8I_A33=y
CONFIG_DRAM_CLK=456
CONFIG_DRAM_ZQ=15291
CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
CONFIG_USB0_ID_DET="PH8"
CONFIG_AXP_GPIO=y
CONFIG_VIDEO_LCD_MODE="x:1024,y:768,depth:18,pclk_khz:65000,le:120,ri:180,up:22,lo:13,hs:20,vs:3,sync:3,vmode:0"
CONFIG_VIDEO_LCD_DCLK_PHASE=0
CONFIG_VIDEO_LCD_POWER="PH7"
CONFIG_VIDEO_LCD_BL_EN="PH6"
CONFIG_VIDEO_LCD_BL_PWM="PH0"
CONFIG_VIDEO_LCD_PANEL_LVDS=y
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_REGULATOR_AXP_USB_POWER=y
CONFIG_AXP_DLDO1_VOLT=3300
# CONFIG_REQUIRE_SERIAL_CONSOLE is not set
CONFIG_CONS_INDEX=5
CONFIG_USB_MUSB_HOST=y
sunxi: Add iNet D978 rev2 defconfig The iNet D978 rev2 is a tablet board designed by iNet, which is intended to use on 10" tablets with a appearance like Apple iPad. It has A33 SoC, 1GB RAM, 8GB/16GB NAND, SDIO Wi-Fi, a MicroUSB port and a MicroSD slot. Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> 2016-08-27 14:16:13 +00:00			`CONFIG_ARM=y`
			`CONFIG_ARCH_SUNXI=y`
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com> 2021-06-28 14:17:29 +00:00			`CONFIG_DEFAULT_DEVICE_TREE="sun8i-a33-inet-d978-rev2"`
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com> 2018-04-08 00:27:54 +00:00			`CONFIG_SPL=y`
sunxi: Add iNet D978 rev2 defconfig The iNet D978 rev2 is a tablet board designed by iNet, which is intended to use on 10" tablets with a appearance like Apple iPad. It has A33 SoC, 1GB RAM, 8GB/16GB NAND, SDIO Wi-Fi, a MicroUSB port and a MicroSD slot. Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> 2016-08-27 14:16:13 +00:00			`CONFIG_MACH_SUN8I_A33=y`
			`CONFIG_DRAM_CLK=456`
			`CONFIG_DRAM_ZQ=15291`
			`CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"`
			`CONFIG_USB0_ID_DET="PH8"`
			`CONFIG_AXP_GPIO=y`
			`CONFIG_VIDEO_LCD_MODE="x:1024,y:768,depth:18,pclk_khz:65000,le:120,ri:180,up:22,lo:13,hs:20,vs:3,sync:3,vmode:0"`
			`CONFIG_VIDEO_LCD_DCLK_PHASE=0`
			`CONFIG_VIDEO_LCD_POWER="PH7"`
			`CONFIG_VIDEO_LCD_BL_EN="PH6"`
			`CONFIG_VIDEO_LCD_BL_PWM="PH0"`
			`CONFIG_VIDEO_LCD_PANEL_LVDS=y`
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com> 2020-07-28 12:46:52 +00:00			`# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set`
sunxi: Switch to PMIC USB power supply VBUS detection Update boards to use the USB power supply driver, as referenced in the device tree, instead of a virtual GPIO. This removes the need for some DM-incompatible special cases in the GPIO driver. The following five boards used AXP0-VBUS-DETECT in their config, but are missing the "usb0_vbus_power-supply" property in their device tree: - Ainol_AW1_defconfig / sun7i-a20-ainol-aw1 - Cubieboard4_defconfig / sun9i-a80-cubieboard4 - Merrii_A80_Optimus_defconfig / sun9i-a80-optimus - Yones_Toptech_BD1078_defconfig / sun7i-a20-yones-toptech-bd1078 - Yones_Toptech_BS1078_V2_defconfig / sun6i-a31s-yones-toptech-bs1078-v2 None of those five boards have the MUSB controller (USB OTG) enabled in their device trees, so this change should not break anything for them. Additionally, the following board intentionally omits the property because VBUS is always enabled: - Nintendo_NES_Classic_Edition_defconfig / sun8i-r16-nintendo-nes-classic The PHY driver already assumes VBUS is enabled when no detection method is available, so again this will not cause any problems. Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com> 2023-01-22 23:46:21 +00:00			`CONFIG_REGULATOR_AXP_USB_POWER=y`
sunxi: Add iNet D978 rev2 defconfig The iNet D978 rev2 is a tablet board designed by iNet, which is intended to use on 10" tablets with a appearance like Apple iPad. It has A33 SoC, 1GB RAM, 8GB/16GB NAND, SDIO Wi-Fi, a MicroUSB port and a MicroSD slot. Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> 2016-08-27 14:16:13 +00:00			`CONFIG_AXP_DLDO1_VOLT=3300`
configs: Resync with savedefconfig Signed-off-by: Tom Rini <trini@konsulko.com> 2016-09-08 20:11:59 +00:00			`# CONFIG_REQUIRE_SERIAL_CONSOLE is not set`
Convert all of CONFIG_CONS_INDEX to Kconfig This converts the following to Kconfig: CONFIG_CONS_INDEX We have existing entries for this option in a number of places, with different guards on them. They're also sometimes used for things not directly inside of the serial driver. First, introduce a new symbol to guard the use of CONFIG_CONS_INDEX, so that in the case where we don't need this for the serial driver, but for some other use, we can still do it. Next, consolidate all of these into the single entry in drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that we can imply a correct value here to make the defconfig side of this smaller. Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Rework a lot of the logic here, such that I took authorship from Adam, but kept his S-o-B line] Signed-off-by: Tom Rini <trini@konsulko.com> 2018-03-07 00:02:27 +00:00			`CONFIG_CONS_INDEX=5`
sunxi: Add iNet D978 rev2 defconfig The iNet D978 rev2 is a tablet board designed by iNet, which is intended to use on 10" tablets with a appearance like Apple iPad. It has A33 SoC, 1GB RAM, 8GB/16GB NAND, SDIO Wi-Fi, a MicroUSB port and a MicroSD slot. Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> 2016-08-27 14:16:13 +00:00			`CONFIG_USB_MUSB_HOST=y`