u-boot/arch/arm/mach-mvebu/include/mach/config.h

106 lines
2.5 KiB
C
Raw Normal View History

/*
* (C) Copyright 2011
* Marvell Semiconductor <www.marvell.com>
* Written-by: Lei Wen <leiwen@marvell.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
/*
* This file should be included in board config header file.
*
* It supports common definitions for MVEBU platforms
*/
#ifndef _MVEBU_CONFIG_H
#define _MVEBU_CONFIG_H
#include <asm/arch/soc.h>
#if defined(CONFIG_ARMADA_XP) || defined(CONFIG_ARMADA_375) \
|| defined(CONFIG_ARMADA_38X)
/*
* Set this for the common xor register definitions needed in dram.c
* for A38x as well here.
*/
#define MV88F78X60 /* for the DDR training bin_hdr code */
#endif
#define CONFIG_SYS_L2_PL310
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
#endif
/*
* By default kwbimage.cfg from board specific folder is used
* If for some board, different configuration file need to be used,
* CONFIG_SYS_KWD_CONFIG should be defined in board specific header file
*/
#ifndef CONFIG_SYS_KWD_CONFIG
#define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage.cfg
#endif /* CONFIG_SYS_KWD_CONFIG */
/* Add target to build it automatically upon "make" */
#ifdef CONFIG_SPL
#define CONFIG_BUILD_TARGET "u-boot-spl.kwb"
#endif
/* end of 16M scrubbed by training in bootrom */
#define CONFIG_SYS_INIT_SP_ADDR 0x00FF0000
#define CONFIG_NR_DRAM_BANKS_MAX 2
#define MV_UART_CONSOLE_BASE MVEBU_UART0_BASE
/*
* SPI Flash configuration
*/
#ifdef CONFIG_CMD_SF
#define CONFIG_KIRKWOOD_SPI
#ifndef CONFIG_ENV_SPI_BUS
# define CONFIG_ENV_SPI_BUS 0
#endif
#ifndef CONFIG_ENV_SPI_CS
# define CONFIG_ENV_SPI_CS 0
#endif
#ifndef CONFIG_ENV_SPI_MAX_HZ
# define CONFIG_ENV_SPI_MAX_HZ 50000000
#endif
#endif
/* Needed for SPI NOR booting in SPL */
#define CONFIG_DM_SEQ_ALIAS 1
/*
* Ethernet Driver configuration
*/
#ifdef CONFIG_CMD_NET
#define CONFIG_MII /* expose smi ove miiphy interface */
#if !defined(CONFIG_ARMADA_375)
#define CONFIG_MVNETA /* Enable Marvell Gbe Controller Driver */
#define CONFIG_PHYLIB
#endif
#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */
#define CONFIG_PHY_GIGE /* GbE speed/duplex detect */
#define CONFIG_ARP_TIMEOUT 200
#define CONFIG_NET_RETRY_COUNT 50
#endif /* CONFIG_CMD_NET */
/*
* I2C related stuff
*/
#ifdef CONFIG_CMD_I2C
#ifndef CONFIG_SYS_I2C_SOFT
#define CONFIG_I2C_MVTWSI
#endif
#define CONFIG_SYS_I2C_SLAVE 0x0
#define CONFIG_SYS_I2C_SPEED 100000
#endif
/* Use common timer */
#define CONFIG_SYS_TIMER_COUNTS_DOWN
#define CONFIG_SYS_TIMER_COUNTER (MVEBU_TIMER_BASE + 0x14)
#define CONFIG_SYS_TIMER_RATE 25000000
#endif /* __MVEBU_CONFIG_H */