2018-05-06 21:58:06 +00:00
|
|
|
// SPDX-License-Identifier: GPL-2.0+
|
2015-10-20 13:14:47 +00:00
|
|
|
/*
|
|
|
|
* Copyright (C) 2015 Stefan Roese <sr@denx.de>
|
|
|
|
*/
|
|
|
|
|
|
|
|
#include <common.h>
|
|
|
|
#include <i2c.h>
|
|
|
|
#include <miiphy.h>
|
|
|
|
#include <netdev.h>
|
|
|
|
#include <asm/io.h>
|
|
|
|
#include <asm/arch/cpu.h>
|
|
|
|
#include <asm/arch/soc.h>
|
|
|
|
|
2018-05-10 01:28:29 +00:00
|
|
|
#include "../drivers/ddr/marvell/a38x/ddr3_init.h"
|
2015-10-20 13:14:47 +00:00
|
|
|
#include <../serdes/a38x/high_speed_env_spec.h>
|
|
|
|
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
|
|
|
|
#define ETH_PHY_CTRL_REG 0
|
|
|
|
#define ETH_PHY_CTRL_POWER_DOWN_BIT 11
|
|
|
|
#define ETH_PHY_CTRL_POWER_DOWN_MASK (1 << ETH_PHY_CTRL_POWER_DOWN_BIT)
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Those values and defines are taken from the Marvell U-Boot version
|
|
|
|
* "u-boot-2013.01-15t1-clearfog"
|
|
|
|
*/
|
|
|
|
#define BOARD_GPP_OUT_ENA_LOW 0xffffffff
|
|
|
|
#define BOARD_GPP_OUT_ENA_MID 0xffffffff
|
|
|
|
|
|
|
|
#define BOARD_GPP_OUT_VAL_LOW 0x0
|
|
|
|
#define BOARD_GPP_OUT_VAL_MID 0x0
|
|
|
|
#define BOARD_GPP_POL_LOW 0x0
|
|
|
|
#define BOARD_GPP_POL_MID 0x0
|
|
|
|
|
|
|
|
/* IO expander on Marvell GP board includes e.g. fan enabling */
|
|
|
|
struct marvell_io_exp {
|
|
|
|
u8 chip;
|
|
|
|
u8 addr;
|
|
|
|
u8 val;
|
|
|
|
};
|
|
|
|
|
|
|
|
static struct marvell_io_exp io_exp[] = {
|
|
|
|
{ 0x20, 2, 0x40 }, /* Deassert both mini pcie reset signals */
|
|
|
|
{ 0x20, 6, 0xf9 },
|
|
|
|
{ 0x20, 2, 0x46 }, /* rst signals and ena USB3 current limiter */
|
|
|
|
{ 0x20, 6, 0xb9 },
|
|
|
|
{ 0x20, 3, 0x00 }, /* Set SFP_TX_DIS to zero */
|
|
|
|
{ 0x20, 7, 0xbf }, /* Drive SFP_TX_DIS to zero */
|
|
|
|
};
|
|
|
|
|
|
|
|
static struct serdes_map board_serdes_map[] = {
|
|
|
|
{SATA0, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0},
|
|
|
|
{SGMII1, SERDES_SPEED_1_25_GBPS, SERDES_DEFAULT_MODE, 0, 0},
|
|
|
|
{PEX1, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0},
|
|
|
|
{USB3_HOST1, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0},
|
|
|
|
{PEX2, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0},
|
|
|
|
{SGMII2, SERDES_SPEED_1_25_GBPS, SERDES_DEFAULT_MODE, 0, 0},
|
|
|
|
};
|
|
|
|
|
|
|
|
int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count)
|
|
|
|
{
|
|
|
|
*serdes_map_array = board_serdes_map;
|
|
|
|
*count = ARRAY_SIZE(board_serdes_map);
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Define the DDR layout / topology here in the board file. This will
|
|
|
|
* be used by the DDR3 init code in the SPL U-Boot version to configure
|
|
|
|
* the DDR3 controller.
|
|
|
|
*/
|
2018-05-10 01:28:29 +00:00
|
|
|
static struct mv_ddr_topology_map board_topology_map = {
|
|
|
|
DEBUG_LEVEL_ERROR,
|
2015-10-20 13:14:47 +00:00
|
|
|
0x1, /* active interfaces */
|
|
|
|
/* cs_mask, mirror, dqs_swap, ck_swap X PUPs */
|
|
|
|
{ { { {0x1, 0, 0, 0},
|
|
|
|
{0x1, 0, 0, 0},
|
|
|
|
{0x1, 0, 0, 0},
|
|
|
|
{0x1, 0, 0, 0},
|
|
|
|
{0x1, 0, 0, 0} },
|
|
|
|
SPEED_BIN_DDR_1600K, /* speed_bin */
|
2018-05-10 01:28:29 +00:00
|
|
|
MV_DDR_DEV_WIDTH_16BIT, /* memory_width */
|
|
|
|
MV_DDR_DIE_CAP_4GBIT, /* mem_size */
|
2015-10-20 13:14:47 +00:00
|
|
|
DDR_FREQ_800, /* frequency */
|
2017-11-28 21:38:34 +00:00
|
|
|
0, 0, /* cas_wl cas_l */
|
2018-05-10 01:28:30 +00:00
|
|
|
MV_DDR_TEMP_LOW, /* temperature */
|
|
|
|
MV_DDR_TIM_DEFAULT} }, /* timing */
|
2018-05-10 01:28:29 +00:00
|
|
|
BUS_MASK_32BIT, /* Busses mask */
|
|
|
|
MV_DDR_CFG_DEFAULT, /* ddr configuration data source */
|
|
|
|
{ {0} }, /* raw spd data */
|
|
|
|
{0} /* timing parameters */
|
2015-10-20 13:14:47 +00:00
|
|
|
};
|
|
|
|
|
2018-05-10 01:28:29 +00:00
|
|
|
struct mv_ddr_topology_map *mv_ddr_topology_map_get(void)
|
2015-10-20 13:14:47 +00:00
|
|
|
{
|
|
|
|
/* Return the board topology as defined in the board code */
|
|
|
|
return &board_topology_map;
|
|
|
|
}
|
|
|
|
|
|
|
|
int board_early_init_f(void)
|
|
|
|
{
|
|
|
|
/* Configure MPP */
|
|
|
|
writel(0x11111111, MVEBU_MPP_BASE + 0x00);
|
|
|
|
writel(0x11111111, MVEBU_MPP_BASE + 0x04);
|
|
|
|
writel(0x10400011, MVEBU_MPP_BASE + 0x08);
|
|
|
|
writel(0x22043333, MVEBU_MPP_BASE + 0x0c);
|
|
|
|
writel(0x44400002, MVEBU_MPP_BASE + 0x10);
|
|
|
|
writel(0x41144004, MVEBU_MPP_BASE + 0x14);
|
|
|
|
writel(0x40333333, MVEBU_MPP_BASE + 0x18);
|
|
|
|
writel(0x00004444, MVEBU_MPP_BASE + 0x1c);
|
|
|
|
|
|
|
|
/* Set GPP Out value */
|
|
|
|
writel(BOARD_GPP_OUT_VAL_LOW, MVEBU_GPIO0_BASE + 0x00);
|
|
|
|
writel(BOARD_GPP_OUT_VAL_MID, MVEBU_GPIO1_BASE + 0x00);
|
|
|
|
|
|
|
|
/* Set GPP Polarity */
|
|
|
|
writel(BOARD_GPP_POL_LOW, MVEBU_GPIO0_BASE + 0x0c);
|
|
|
|
writel(BOARD_GPP_POL_MID, MVEBU_GPIO1_BASE + 0x0c);
|
|
|
|
|
|
|
|
/* Set GPP Out Enable */
|
|
|
|
writel(BOARD_GPP_OUT_ENA_LOW, MVEBU_GPIO0_BASE + 0x04);
|
|
|
|
writel(BOARD_GPP_OUT_ENA_MID, MVEBU_GPIO1_BASE + 0x04);
|
|
|
|
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
int board_init(void)
|
|
|
|
{
|
|
|
|
int i;
|
|
|
|
|
|
|
|
/* Address of boot parameters */
|
|
|
|
gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
|
|
|
|
|
|
|
|
/* Toggle GPIO41 to reset onboard switch and phy */
|
|
|
|
clrbits_le32(MVEBU_GPIO1_BASE + 0x0, BIT(9));
|
|
|
|
clrbits_le32(MVEBU_GPIO1_BASE + 0x4, BIT(9));
|
2017-05-09 11:54:44 +00:00
|
|
|
/* GPIO 19 on ClearFog rev 2.1 controls the uSOM onboard phy reset */
|
|
|
|
clrbits_le32(MVEBU_GPIO0_BASE + 0x0, BIT(19));
|
|
|
|
clrbits_le32(MVEBU_GPIO0_BASE + 0x4, BIT(19));
|
2015-10-20 13:14:47 +00:00
|
|
|
mdelay(1);
|
|
|
|
setbits_le32(MVEBU_GPIO1_BASE + 0x0, BIT(9));
|
2017-05-09 11:54:44 +00:00
|
|
|
setbits_le32(MVEBU_GPIO0_BASE + 0x0, BIT(19));
|
2015-10-20 13:14:47 +00:00
|
|
|
mdelay(10);
|
|
|
|
|
|
|
|
/* Init I2C IO expanders */
|
|
|
|
for (i = 0; i < ARRAY_SIZE(io_exp); i++)
|
|
|
|
i2c_write(io_exp[i].chip, io_exp[i].addr, 1, &io_exp[i].val, 1);
|
|
|
|
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
int checkboard(void)
|
|
|
|
{
|
|
|
|
puts("Board: SolidRun ClearFog\n");
|
|
|
|
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
int board_eth_init(bd_t *bis)
|
|
|
|
{
|
|
|
|
cpu_eth_init(bis); /* Built in controller(s) come first */
|
|
|
|
return pci_eth_init(bis);
|
|
|
|
}
|