u-boot/configs/inet_q972_defconfig

CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
CONFIG_DEFAULT_DEVICE_TREE="sun6i-a31s-inet-q972"
CONFIG_SPL=y
CONFIG_MACH_SUN6I=y
CONFIG_DRAM_CLK=384
CONFIG_DRAM_ZQ=251
CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
CONFIG_USB0_ID_DET="PA15"
CONFIG_AXP_GPIO=y
CONFIG_VIDEO_LCD_MODE="x:1024,y:768,depth:18,pclk_khz:65000,le:280,ri:20,up:22,lo:8,hs:20,vs:8,sync:3,vmode:0"
CONFIG_VIDEO_LCD_DCLK_PHASE=0
CONFIG_VIDEO_LCD_BL_EN="PA25"
CONFIG_VIDEO_LCD_BL_PWM="PH13"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_REGULATOR_AXP_USB_POWER=y
CONFIG_AXP_DLDO1_VOLT=3300
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_OHCI_HCD=y
CONFIG_USB_MUSB_HOST=y
sun6i: Add defconfig and dts file for tablets using the inet-q972 PCB Add a defconfig and dts file for tablets using the generic inet-q972 PCB. Tablets with this PCB feature a mini-hdmi output, micro-usb usb-host, micro-usb usb-otg, 3.5mm headphone jack, a micro sd slot, (mini) power-barrel and an usb wifi module. This has been tested on a 9.7" 1024x768 qware qw tb9718-qhd tablet. The dts files are identical to the ones submitted to the upstream kernel. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> 2016-08-18 19:50:42 +02:00			`CONFIG_ARM=y`
			`CONFIG_ARCH_SUNXI=y`
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com> 2021-06-28 10:17:29 -04:00			`CONFIG_DEFAULT_DEVICE_TREE="sun6i-a31s-inet-q972"`
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com> 2018-04-07 20:27:54 -04:00			`CONFIG_SPL=y`
sun6i: Add defconfig and dts file for tablets using the inet-q972 PCB Add a defconfig and dts file for tablets using the generic inet-q972 PCB. Tablets with this PCB feature a mini-hdmi output, micro-usb usb-host, micro-usb usb-otg, 3.5mm headphone jack, a micro sd slot, (mini) power-barrel and an usb wifi module. This has been tested on a 9.7" 1024x768 qware qw tb9718-qhd tablet. The dts files are identical to the ones submitted to the upstream kernel. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> 2016-08-18 19:50:42 +02:00			`CONFIG_MACH_SUN6I=y`
			`CONFIG_DRAM_CLK=384`
			`CONFIG_DRAM_ZQ=251`
			`CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"`
			`CONFIG_USB0_ID_DET="PA15"`
			`CONFIG_AXP_GPIO=y`
			`CONFIG_VIDEO_LCD_MODE="x:1024,y:768,depth:18,pclk_khz:65000,le:280,ri:20,up:22,lo:8,hs:20,vs:8,sync:3,vmode:0"`
			`CONFIG_VIDEO_LCD_DCLK_PHASE=0`
			`CONFIG_VIDEO_LCD_BL_EN="PA25"`
			`CONFIG_VIDEO_LCD_BL_PWM="PH13"`
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com> 2020-07-28 08:46:52 -04:00			`# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set`
sunxi: Switch to PMIC USB power supply VBUS detection Update boards to use the USB power supply driver, as referenced in the device tree, instead of a virtual GPIO. This removes the need for some DM-incompatible special cases in the GPIO driver. The following five boards used AXP0-VBUS-DETECT in their config, but are missing the "usb0_vbus_power-supply" property in their device tree: - Ainol_AW1_defconfig / sun7i-a20-ainol-aw1 - Cubieboard4_defconfig / sun9i-a80-cubieboard4 - Merrii_A80_Optimus_defconfig / sun9i-a80-optimus - Yones_Toptech_BD1078_defconfig / sun7i-a20-yones-toptech-bd1078 - Yones_Toptech_BS1078_V2_defconfig / sun6i-a31s-yones-toptech-bs1078-v2 None of those five boards have the MUSB controller (USB OTG) enabled in their device trees, so this change should not break anything for them. Additionally, the following board intentionally omits the property because VBUS is always enabled: - Nintendo_NES_Classic_Edition_defconfig / sun8i-r16-nintendo-nes-classic The PHY driver already assumes VBUS is enabled when no detection method is available, so again this will not cause any problems. Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com> 2023-01-22 17:46:21 -06:00			`CONFIG_REGULATOR_AXP_USB_POWER=y`
sun6i: Add defconfig and dts file for tablets using the inet-q972 PCB Add a defconfig and dts file for tablets using the generic inet-q972 PCB. Tablets with this PCB feature a mini-hdmi output, micro-usb usb-host, micro-usb usb-otg, 3.5mm headphone jack, a micro sd slot, (mini) power-barrel and an usb wifi module. This has been tested on a 9.7" 1024x768 qware qw tb9718-qhd tablet. The dts files are identical to the ones submitted to the upstream kernel. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> 2016-08-18 19:50:42 +02:00			`CONFIG_AXP_DLDO1_VOLT=3300`
			`CONFIG_USB_EHCI_HCD=y`
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com> 2019-02-07 14:53:03 -05:00			`CONFIG_USB_OHCI_HCD=y`
configs: Resync with savedefconfig Signed-off-by: Tom Rini <trini@konsulko.com> 2016-09-08 16:11:59 -04:00			`CONFIG_USB_MUSB_HOST=y`